Volkswagen Vehicle Models Volkswagen Atlas 2018-present
Volkswagen Vehicle Models Volkswagen Atlas 2018-present Torque Specifications
Complete Volkswagen Vehicle Models Volkswagen Atlas 2018-present torque specifications guide. Includes factory-specified torque values, torque sequences, and technical specifications for all components including body, brakes, drivetrain, electrical, emissions sensors, fuel, exhaust, HVAC, and suspension. Essential information for proper assembly and maintenance.
Updated
Important Information
Safety guidelines and reference information for proper torque application
Safety First
- Always verify torque specifications with your vehicle's factory service manual
- Use properly calibrated torque wrenches
- Replace all torque-to-yield (TTY) bolts - they are single-use only
- When in doubt, consult a professional mechanic
Quick Reference Guide
Quick Reference Guide
ft-lbs → Nm
× 1.356
ft-lbs → kg-m
× 0.138
Nm → ft-lbs
× 0.738
in-lbs → ft-lbs
× 0.083
Common Torque Patterns
Star Pattern
Used for wheels and other circular bolt patterns
Cross Pattern
Used for gaskets and cover plates
Sequential Pattern
Used for head bolts and other critical components
Common Mistakes to Avoid
Common Mistakes to Avoid
Over-tightening
Exceeding the specified torque value can stretch or break fasteners, damage threads, or crack components.
Prevention:
Always use a calibrated torque wrench and follow specifications exactly.
Incorrect Torque Sequence
Tightening bolts in the wrong order can cause uneven pressure distribution and potential leaks or damage.
Prevention:
Follow the manufacturer's specified torque sequence pattern.
Dirty Threads
Dirt, rust, or old thread locker can affect torque readings and proper fastener tension.
Prevention:
Clean and inspect all threads before assembly. Use new thread locker if specified.
Reusing TTY Bolts
Torque-to-yield bolts are designed to stretch and must not be reused.
Prevention:
Always replace TTY bolts with new ones. They are single-use only.
Dry vs. Lubricated
Not accounting for whether torque specs are for dry or lubricated fasteners can lead to incorrect tension.
Prevention:
Check if specs are for dry or lubricated threads. Use specified lubricant when required.
Recommended Tools
Recommended Tools
Torque Wrench (1/4" Drive)
Range: 2-25 ft-lbs
Small fasteners, delicate components
Torque Wrench (3/8" Drive)
Range: 10-100 ft-lbs
Most common automotive fasteners
Torque Wrench (1/2" Drive)
Range: 30-250 ft-lbs
Large fasteners, wheels
Angle Gauge
Torque-to-yield (TTY) bolts
Torque Wrench Care
- Calibrate annually or after 5,000 clicks
- Store at lowest setting
- Keep clean and lubricated
Search Specifications
Search by component name, bolt size, or description
Type to search through torque specifications. Use arrow keys to navigate results. Press Enter to select a result.
Torque Calculator
Convert between different torque units
2.0l I4 Engine
Torque specifications for 2.0L-I4 Engine
2.0l I4 Engine
Torque specifications for 2.0L-I4 Engine
Cylinder Head
1 Cylinder Head Bolts
M10 x 1.25
1
Cylinder Head Bolts
M10 x 1.25
Torque Specification
1. 15 ft-lbs (20 N·m)
2. 90°
Important Notes
Follow the manufacturer's torque sequence diagram. Final torque is achieved by turning the bolts an additional 90 degrees.
2 Valve Cover Bolts
M6 x 1.0
2
Valve Cover Bolts
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure the valve cover gasket is properly seated before tightening.
Crankshaft And Bearings
1 Main Bearing Bolts
M12 x 1.5
1
Main Bearing Bolts
M12 x 1.5
Torque Specification
48 ft-lbs (65 N·m)
Important Notes
Follow the manufacturer's torque sequence diagram. Ensure bearings are properly seated before tightening.
2 Connecting Rod Nuts
M8 x 1.25
2
Connecting Rod Nuts
M8 x 1.25
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
Ensure connecting rod bearings are properly seated before tightening.
Timing System
1 Camshaft Sprocket Bolt
M10 x 1.25
1
Camshaft Sprocket Bolt
M10 x 1.25
Torque Specification
66 ft-lbs (90 N·m)
Important Notes
Ensure the timing marks are aligned before tightening.
2 Timing Belt/Chain Tensioner Bolt
M8 x 1.25
2
Timing Belt/Chain Tensioner Bolt
M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Ensure proper tension on the timing belt/chain before tightening.
Intake And Exhaust
1 Intake Manifold Bolts
M8 x 1.25
1
Intake Manifold Bolts
M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Follow the manufacturer's torque sequence diagram.
2 Exhaust Manifold Bolts
M8 x 1.25
2
Exhaust Manifold Bolts
M8 x 1.25
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
Ensure the exhaust manifold gasket is properly seated before tightening.
Lubrication System
1 Oil Pan Bolts
M6 x 1.0
1
Oil Pan Bolts
M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Ensure the oil pan gasket is properly seated before tightening.
2 Oil Drain Plug Bolt
M14 x 1.5
2
Oil Drain Plug Bolt
M14 x 1.5
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Replace the crush washer with a new one during installation.
Turbocharger System
1 Turbocharger Mounting Bolts
M8 x 1.25
1
Turbocharger Mounting Bolts
M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Ensure the turbocharger gasket is properly seated before tightening.
2 Turbocharger Oil Feed Line Bolts
M6 x 1.0
2
Turbocharger Oil Feed Line Bolts
M6 x 1.0
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Ensure the oil feed line is properly aligned before tightening.
2.0l I4 Turbo Engine
Torque specifications for 2.0L-I4-TURBO Engine
2.0l I4 Turbo Engine
Torque specifications for 2.0L-I4-TURBO Engine
Cylinder Head
1 Cylinder Head Bolts
M10 x 1.25
1
Cylinder Head Bolts
M10 x 1.25
Torque Specification
1. 15 ft-lbs (20 N·m)
2. 90°
Important Notes
Follow the manufacturer's torque sequence diagram. Final torque is achieved by turning the bolts an additional 90 degrees.
2 Valve Cover Bolts
M6 x 1.0
2
Valve Cover Bolts
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure the valve cover gasket is properly seated before tightening.
Crankshaft And Bearings
1 Main Bearing Bolts
M12 x 1.5
1
Main Bearing Bolts
M12 x 1.5
Torque Specification
48 ft-lbs (65 N·m)
Important Notes
Follow the manufacturer's torque sequence diagram. Ensure bearings are properly seated before tightening.
2 Connecting Rod Nuts
M8 x 1.25
2
Connecting Rod Nuts
M8 x 1.25
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
Ensure connecting rod bearings are properly seated before tightening.
Timing System
1 Camshaft Sprocket Bolt
M10 x 1.25
1
Camshaft Sprocket Bolt
M10 x 1.25
Torque Specification
66 ft-lbs (90 N·m)
Important Notes
Ensure the timing marks are aligned before tightening.
2 Timing Belt/Chain Tensioner Bolt
M8 x 1.25
2
Timing Belt/Chain Tensioner Bolt
M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Ensure proper tension on the timing belt/chain before tightening.
Intake And Exhaust
1 Intake Manifold Bolts
M8 x 1.25
1
Intake Manifold Bolts
M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Follow the manufacturer's torque sequence diagram.
2 Exhaust Manifold Bolts
M8 x 1.25
2
Exhaust Manifold Bolts
M8 x 1.25
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
Ensure the exhaust manifold gasket is properly seated before tightening.
Lubrication System
1 Oil Pan Bolts
M6 x 1.0
1
Oil Pan Bolts
M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Ensure the oil pan gasket is properly seated before tightening.
2 Oil Drain Plug Bolt
M14 x 1.5
2
Oil Drain Plug Bolt
M14 x 1.5
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Replace the crush washer with a new one during installation.
Turbocharger System
1 Turbocharger Mounting Bolts
M8 x 1.25
1
Turbocharger Mounting Bolts
M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Ensure the turbocharger gasket is properly seated before tightening.
2 Turbocharger Oil Feed Line Bolts
M6 x 1.0
2
Turbocharger Oil Feed Line Bolts
M6 x 1.0
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Ensure the oil feed line is properly aligned before tightening.
3.6l Engine
Torque specifications for 3.6L Engine
3.6l Engine
Torque specifications for 3.6L Engine
Cylinder Head
1 Cylinder Head Bolts
M10 x 1.5
1
Cylinder Head Bolts
M10 x 1.5
Torque Specification
1. 15 ft-lbs (20 N·m)
2. 90°
Important Notes
Follow the manufacturer's specified torque sequence for proper sealing.
2 Rocker Arms/Shafts Bolts
M8 x 1.25
2
Rocker Arms/Shafts Bolts
M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Ensure proper alignment of rocker arms before tightening.
3 Valve Cover Bolts
M6 x 1.0
3
Valve Cover Bolts
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Use a new gasket and ensure the sealing surface is clean.
Crankshaft And Bearings
1 Main Bearing Bolts
M12 x 1.75
1
Main Bearing Bolts
M12 x 1.75
Torque Specification
48 ft-lbs (65 N·m)
Important Notes
Ensure proper alignment of main bearings before tightening.
2 Connecting Rod Nuts
M10 x 1.25
2
Connecting Rod Nuts
M10 x 1.25
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
Ensure proper alignment of connecting rods before tightening.
3 Flywheel Bolts
M12 x 1.75
3
Flywheel Bolts
M12 x 1.75
Torque Specification
75 ft-lbs (101 N·m)
Important Notes
Use thread locker on flywheel bolts as specified by the manufacturer.
Timing System
1 Timing Belt/Chain Tensioner Bolt
M8 x 1.25
1
Timing Belt/Chain Tensioner Bolt
M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Ensure proper tension on the timing belt/chain before tightening.
2 Camshaft Sprocket Bolt
M10 x 1.5
2
Camshaft Sprocket Bolt
M10 x 1.5
Torque Specification
66 ft-lbs (90 N·m)
Important Notes
Ensure proper alignment of the camshaft sprocket before tightening.
Intake And Exhaust
1 Intake Manifold Bolts
M8 x 1.25
1
Intake Manifold Bolts
M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Use a new gasket and ensure the sealing surface is clean.
2 Exhaust Manifold/Headers Bolts
M10 x 1.5
2
Exhaust Manifold/Headers Bolts
M10 x 1.5
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
Use new gaskets and ensure proper alignment before tightening.
Lubrication System
1 Oil Pan Bolts
M6 x 1.0
1
Oil Pan Bolts
M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Use a new gasket and ensure the sealing surface is clean.
2 Oil Pump Bolts
M8 x 1.25
2
Oil Pump Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Ensure proper alignment of the oil pump before tightening.
3.6l V6 Engine
Torque specifications for 3.6L-V6 Engine
3.6l V6 Engine
Torque specifications for 3.6L-V6 Engine
Cylinder Head
1 Cylinder Head Bolts
M10 x 1.5
1
Cylinder Head Bolts
M10 x 1.5
Torque Specification
1. 15 ft-lbs (20 N·m)
2. 90°
Important Notes
Follow the manufacturer's specified torque sequence for proper sealing.
2 Rocker Arms/Shafts Bolts
M8 x 1.25
2
Rocker Arms/Shafts Bolts
M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Ensure proper alignment of rocker arms before tightening.
3 Valve Cover Bolts
M6 x 1.0
3
Valve Cover Bolts
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Use a new gasket and ensure the sealing surface is clean.
Crankshaft And Bearings
1 Main Bearing Bolts
M12 x 1.75
1
Main Bearing Bolts
M12 x 1.75
Torque Specification
48 ft-lbs (65 N·m)
Important Notes
Ensure proper alignment of main bearings before tightening.
2 Connecting Rod Nuts
M10 x 1.25
2
Connecting Rod Nuts
M10 x 1.25
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
Ensure proper alignment of connecting rods before tightening.
3 Flywheel Bolts
M12 x 1.75
3
Flywheel Bolts
M12 x 1.75
Torque Specification
75 ft-lbs (101 N·m)
Important Notes
Use thread locker on flywheel bolts as specified by the manufacturer.
Timing System
1 Timing Belt/Chain Tensioner Bolt
M8 x 1.25
1
Timing Belt/Chain Tensioner Bolt
M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Ensure proper tension on the timing belt/chain before tightening.
2 Camshaft Sprocket Bolt
M10 x 1.5
2
Camshaft Sprocket Bolt
M10 x 1.5
Torque Specification
66 ft-lbs (90 N·m)
Important Notes
Ensure proper alignment of the camshaft sprocket before tightening.
Intake And Exhaust
1 Intake Manifold Bolts
M8 x 1.25
1
Intake Manifold Bolts
M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Use a new gasket and ensure the sealing surface is clean.
2 Exhaust Manifold/Headers Bolts
M10 x 1.5
2
Exhaust Manifold/Headers Bolts
M10 x 1.5
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
Use new gaskets and ensure proper alignment before tightening.
Lubrication System
1 Oil Pan Bolts
M6 x 1.0
1
Oil Pan Bolts
M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Use a new gasket and ensure the sealing surface is clean.
2 Oil Pump Bolts
M8 x 1.25
2
Oil Pump Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Ensure proper alignment of the oil pump before tightening.
Body
Torque specifications for Body
Body
Torque specifications for Body
Suspension And Steering
1 Wheel Lug Nuts
M14 x 1.5
1
Wheel Lug Nuts
M14 x 1.5
Torque Specification
148 ft-lbs (200 N·m)
Important Notes
Ensure proper tightening sequence (star pattern) to prevent wheel warping.
2 Strut/Shock Absorber Mounting Bolts
M10 x 1.25
2
Strut/Shock Absorber Mounting Bolts
M10 x 1.25
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Ensure suspension is at ride height before torquing.
3 Control Arm Bolts
M12 x 1.75
3
Control Arm Bolts
M12 x 1.75
Torque Specification
81 ft-lbs (110 N·m)
Important Notes
Ensure suspension is at ride height before torquing.
4 Ball Joint Nut
M10 x 1.25
4
Ball Joint Nut
M10 x 1.25
Torque Specification
52 ft-lbs (70 N·m)
Important Notes
Ensure proper alignment of the ball joint before torquing.
5 Tie Rod End Nut
M8 x 1.25
5
Tie Rod End Nut
M8 x 1.25
Torque Specification
33 ft-lbs (45 N·m)
Important Notes
Ensure proper alignment of the tie rod end before torquing.
6 Sway Bar Link Nut
M10 x 1.25
6
Sway Bar Link Nut
M10 x 1.25
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure sway bar is properly aligned before torquing.
7 Steering Gear/Rack Bolts
M12 x 1.75
7
Steering Gear/Rack Bolts
M12 x 1.75
Torque Specification
81 ft-lbs (110 N·m)
Important Notes
Follow the specified tightening sequence for steering rack bolts.
Braking System
1 Brake Caliper Bolts
M8 x 1.25
1
Brake Caliper Bolts
M8 x 1.25
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Ensure caliper is properly aligned before torquing.
2 Brake Caliper Mounting Bracket Bolts
M12 x 1.75
2
Brake Caliper Mounting Bracket Bolts
M12 x 1.75
Torque Specification
81 ft-lbs (110 N·m)
Important Notes
Ensure bracket is properly aligned before torquing.
3 Brake Disc/Drum Retaining Bolts
M6 x 1.0
3
Brake Disc/Drum Retaining Bolts
M6 x 1.0
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Ensure disc/drum is properly seated before torquing.
Fuel System
1 Fuel Tank Strap Bolts
M8 x 1.25
1
Fuel Tank Strap Bolts
M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Ensure fuel tank is properly aligned before torquing.
2 Fuel Filler Neck Bolts
M6 x 1.0
2
Fuel Filler Neck Bolts
M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Ensure filler neck is properly aligned before torquing.
Electrical System
1 Battery Terminal Nuts
M6 x 1.0
1
Battery Terminal Nuts
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure terminals are clean and properly seated before torquing.
Safety System
1 Seat Belt Anchor Bolts
M10 x 1.25
1
Seat Belt Anchor Bolts
M10 x 1.25
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure seat belt anchor is properly aligned before torquing.
2 Seat Mounting Bolts
M10 x 1.25
2
Seat Mounting Bolts
M10 x 1.25
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Follow the specified tightening sequence for seat mounting bolts.
Body Panels
1 Door Hinge Bolts
M8 x 1.25
1
Door Hinge Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Ensure door is properly aligned before torquing.
2 Hood Hinge Bolts
M8 x 1.25
2
Hood Hinge Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Ensure hood is properly aligned before torquing.
3 Liftgate/Tailgate Hinge Bolts
M8 x 1.25
3
Liftgate/Tailgate Hinge Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Ensure liftgate/tailgate is properly aligned before torquing.
4 Roof Rack Mounting Bolts
M8 x 1.25
4
Roof Rack Mounting Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Ensure roof rack is properly aligned before torquing.
5 Bumper Mounting Bolts
M8 x 1.25
5
Bumper Mounting Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Ensure bumper is properly aligned before torquing.
6 Radiator Support Bolts
M8 x 1.25
6
Radiator Support Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Ensure radiator support is properly aligned before torquing.
Brakes
Torque specifications for Brakes
Brakes
Torque specifications for Brakes
Brake Caliper
1 Brake Caliper Bolts
M10 x 1.25
1
Brake Caliper Bolts
M10 x 1.25
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Ensure the caliper is properly aligned before tightening.
2 Brake Caliper Mounting Bracket Bolts
M12 x 1.5
2
Brake Caliper Mounting Bracket Bolts
M12 x 1.5
Torque Specification
81 ft-lbs (110 N·m)
Important Notes
Ensure the bracket is securely attached to the steering knuckle or axle.
Brake Rotor
1 Brake Disc/Drum Retaining Bolts
M8 x 1.25
1
Brake Disc/Drum Retaining Bolts
M8 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Ensure the rotor is properly seated on the hub before tightening.
Brake Hydraulics
1 Brake Hose Banjo Bolt
M10 x 1.0
1
Brake Hose Banjo Bolt
M10 x 1.0
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Ensure the banjo fitting is properly aligned before tightening.
2 Brake Master Cylinder Mounting Bolts
M8 x 1.25
2
Brake Master Cylinder Mounting Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Ensure the master cylinder is properly aligned before tightening.
3 Brake Booster Mounting Bolts
M8 x 1.25
3
Brake Booster Mounting Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Ensure the booster is properly aligned before tightening.
Brake Pedal
1 Brake Pedal Assembly Bolts
M8 x 1.25
1
Brake Pedal Assembly Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Ensure the pedal assembly is properly aligned before tightening.
Wheel Assembly
1 Wheel Lug Nuts
M12 x 1.5
1
Wheel Lug Nuts
M12 x 1.5
Torque Specification
148 ft-lbs (200 N·m)
Important Notes
Always use a star pattern when tightening lug nuts to ensure even pressure.
Drivetrain
Torque specifications for Drivetrain
Drivetrain
Torque specifications for Drivetrain
Flywheel
1 Flywheel Bolts
M10 x 1.25
1
Flywheel Bolts
M10 x 1.25
Torque Specification
75 ft-lbs (101 N·m)
Important Notes
Ensure the flywheel is properly aligned before tightening. Use a crisscross pattern for even torque distribution.
Transmission Mounting
1 Transmission Mounting Bolts
M8 x 1.25
1
Transmission Mounting Bolts
M8 x 1.25
Torque Specification
48 ft-lbs (65 N·m)
Important Notes
Ensure the transmission is properly aligned before tightening. Use a crisscross pattern for even torque distribution.
Transmission Oil Pan
1 Transmission Oil Pan Bolts
M6 x 1.0
1
Transmission Oil Pan Bolts
M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Ensure the oil pan gasket is properly seated before tightening. Use a crisscross pattern for even torque distribution.
Transmission Plugs
1 Transmission Drain Plug
M12 x 1.5
1
Transmission Drain Plug
M12 x 1.5
Torque Specification
44 ft-lbs (60 N·m)
Important Notes
Ensure the plug is properly seated before tightening. Use a new crush washer if required.
2 Transmission Fill Plug
M12 x 1.5
2
Transmission Fill Plug
M12 x 1.5
Torque Specification
44 ft-lbs (60 N·m)
Important Notes
Ensure the plug is properly seated before tightening. Use a new crush washer if required.
Drive Axle
1 Drive Axle/Half Shaft Bolts
M10 x 1.25
1
Drive Axle/Half Shaft Bolts
M10 x 1.25
Torque Specification
44 ft-lbs (60 N·m)
Important Notes
Ensure the axle is properly aligned before tightening. Use a crisscross pattern for even torque distribution.
Cv Joint
1 CV Joint/Axle Nut
M24 x 1.5
1
CV Joint/Axle Nut
M24 x 1.5
Torque Specification
181 ft-lbs (245 N·m)
Important Notes
Ensure the nut is properly seated before tightening. Use a new cotter pin if required.
Propeller Shaft
1 Propeller/Drive Shaft Bolts
M10 x 1.25
1
Propeller/Drive Shaft Bolts
M10 x 1.25
Torque Specification
44 ft-lbs (60 N·m)
Important Notes
Ensure the drive shaft is properly aligned before tightening. Use a crisscross pattern for even torque distribution.
Differential Plugs
1 Differential Drain Plug
M12 x 1.5
1
Differential Drain Plug
M12 x 1.5
Torque Specification
48 ft-lbs (65 N·m)
Important Notes
Ensure the plug is properly seated before tightening. Use a new crush washer if required.
2 Differential Fill Plug
M12 x 1.5
2
Differential Fill Plug
M12 x 1.5
Torque Specification
48 ft-lbs (65 N·m)
Important Notes
Ensure the plug is properly seated before tightening. Use a new crush washer if required.
Transfer Case Plugs
1 Transfer Case Drain Plug
M10 x 1.25
1
Transfer Case Drain Plug
M10 x 1.25
Torque Specification
29 ft-lbs (40 N·m)
Important Notes
Ensure the plug is properly seated before tightening. Use a new crush washer if required.
2 Transfer Case Fill Plug
M10 x 1.25
2
Transfer Case Fill Plug
M10 x 1.25
Torque Specification
29 ft-lbs (40 N·m)
Important Notes
Ensure the plug is properly seated before tightening. Use a new crush washer if required.
Differential Mounting
1 Differential Mounting Bolts
M10 x 1.25
1
Differential Mounting Bolts
M10 x 1.25
Torque Specification
48 ft-lbs (65 N·m)
Important Notes
Ensure the differential is properly aligned before tightening. Use a crisscross pattern for even torque distribution.
Transfer Case Mounting
1 Transfer Case Mounting Bolts
M10 x 1.25
1
Transfer Case Mounting Bolts
M10 x 1.25
Torque Specification
48 ft-lbs (65 N·m)
Important Notes
Ensure the transfer case is properly aligned before tightening. Use a crisscross pattern for even torque distribution.
Rear Axle Hub
1 Rear Axle Hub Bolts
M12 x 1.5
1
Rear Axle Hub Bolts
M12 x 1.5
Torque Specification
148 ft-lbs (200 N·m)
Important Notes
Ensure the hub is properly aligned before tightening. Use a crisscross pattern for even torque distribution.
Front Axle Hub
1 Front Axle Hub Bolts
M12 x 1.5
1
Front Axle Hub Bolts
M12 x 1.5
Torque Specification
148 ft-lbs (200 N·m)
Important Notes
Ensure the hub is properly aligned before tightening. Use a crisscross pattern for even torque distribution.
Transfer Case Output Shaft
1 Transfer Case Output Shaft Bolts
M10 x 1.25
1
Transfer Case Output Shaft Bolts
M10 x 1.25
Torque Specification
44 ft-lbs (60 N·m)
Important Notes
Ensure the output shafts are properly aligned before tightening. Use a crisscross pattern for even torque distribution.
Dsg7 Transmission
Torque specifications for Dsg7 Transmission
Dsg7 Transmission
Torque specifications for Dsg7 Transmission
Transmission Mounting
1 Transmission Mounting Bolts
M12 x 1.5
1
Transmission Mounting Bolts
M12 x 1.5
Torque Specification
48 ft-lbs (65 N·m)
Important Notes
These bolts ensure proper alignment and prevent damage to the transmission.
Transmission Oil Pan
1 Transmission Oil Pan Bolts
M8 x 1.25
1
Transmission Oil Pan Bolts
M8 x 1.25
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
These bolts prevent oil leaks and ensure proper lubrication of the transmission.
Transmission Fluid Drain and Fill
1 Transmission Drain and Fill Plugs
M14 x 1.5
1
Transmission Drain and Fill Plugs
M14 x 1.5
Torque Specification
44 ft-lbs (60 N·m)
Important Notes
These plugs ensure a leak-free seal and proper transmission fluid pressure.
2 Transmission Fluid Drain/Fill Plug
M12 x 1.5
2
Transmission Fluid Drain/Fill Plug
M12 x 1.5
Torque Specification
29 ft-lbs (40 N·m)
Important Notes
This plug ensures a leak-free seal and proper transmission fluid pressure.
Transmission Case
1 DSG7 Transmission Case Bolts
M10 x 1.5
1
DSG7 Transmission Case Bolts
M10 x 1.5
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
These bolts ensure proper alignment and prevent damage to the transmission. (Estimated value)
Transmission Clutch Pack
1 DSG7 Transmission Clutch Pack Bolts
M8 x 1.25
1
DSG7 Transmission Clutch Pack Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
These bolts ensure proper engagement and disengagement of the clutch. (Estimated value)
Transmission Gearbox
1 DSG7 Transmission Gearbox Bolts
M12 x 1.75
1
DSG7 Transmission Gearbox Bolts
M12 x 1.75
Torque Specification
50 ft-lbs (68 N·m)
Important Notes
These bolts ensure proper alignment and prevent damage to the transmission. (Estimated value)
Transmission Mechatronic Unit
1 DSG7 Transmission Mechatronic Unit Bolts
M6 x 1.0
1
DSG7 Transmission Mechatronic Unit Bolts
M6 x 1.0
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
These bolts ensure proper communication and control of the transmission. (Estimated value)
Electrical
Torque specifications for Electrical
Electrical
Torque specifications for Electrical
Ignition System
1 Ignition Coil Bolt
M6 x 1.0
1
Ignition Coil Bolt
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure the ignition coil is properly seated before tightening.
Charging System
1 Alternator Mounting Bolts
M8 x 1.25
1
Alternator Mounting Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Ensure the alternator is properly aligned with the belt before tightening.
Battery System
1 Battery Terminal Nuts
M6 x 1.0
1
Battery Terminal Nuts
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure the terminals are clean and free of corrosion before tightening.
Starting System
1 Starter Motor Mounting Bolts
M10 x 1.5
1
Starter Motor Mounting Bolts
M10 x 1.5
Torque Specification
33 ft-lbs (45 N·m)
Important Notes
Ensure the starter motor is properly aligned with the flywheel before tightening.
Ac System
1 A/C Compressor Mounting Bolts
M8 x 1.25
1
A/C Compressor Mounting Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Ensure the compressor is properly aligned with the belt before tightening.
2 A/C Line Fittings
M8 x 1.25
2
A/C Line Fittings
M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Ensure the fittings are properly seated before tightening.
Grounding System
1 Ground Strap Bolts
M6 x 1.0
1
Ground Strap Bolts
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure the ground strap is clean and free of corrosion before tightening.
Fuse Box
1 Fuse Box Mounting Bolts
M6 x 1.0
1
Fuse Box Mounting Bolts
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure the fuse box is properly aligned before tightening.
Ecu
1 ECU Mounting Bolts
M6 x 1.0
1
ECU Mounting Bolts
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure the ECU is properly seated before tightening.
Wiring Harness
1 Wiring Harness Clamp Bolts
M6 x 1.0
1
Wiring Harness Clamp Bolts
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure the wiring harness is properly routed before tightening.
Sensors
1 Crankshaft Position Sensor Mounting Bolt
M6 x 1.0
1
Crankshaft Position Sensor Mounting Bolt
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure the sensor is properly seated before tightening.
2 Camshaft Position Sensor Mounting Bolt
M6 x 1.0
2
Camshaft Position Sensor Mounting Bolt
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure the sensor is properly seated before tightening.
Emissions Sensors
Torque specifications for Emissions_sensors
Emissions Sensors
Torque specifications for Emissions_sensors
Exhaust Manifold Headers
1 Exhaust Manifold/Headers Bolts
M10 x 1.25
1
Exhaust Manifold/Headers Bolts
M10 x 1.25
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
Ensure proper sealing to prevent exhaust leaks.
2 Exhaust Manifold/Headers to Cylinder Head Bolts
M8 x 1.25
2
Exhaust Manifold/Headers to Cylinder Head Bolts
M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Ensure proper sealing to prevent exhaust leaks.
Exhaust Pipe Connections
1 Exhaust Pipe to Exhaust Manifold/Headers Bolts
M10 x 1.25
1
Exhaust Pipe to Exhaust Manifold/Headers Bolts
M10 x 1.25
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
Ensure proper sealing to prevent exhaust leaks.
2 Catalytic Converter to Exhaust Pipe Bolts
M10 x 1.25
2
Catalytic Converter to Exhaust Pipe Bolts
M10 x 1.25
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
Ensure proper sealing to prevent exhaust leaks.
Emissions Sensors
1 Oxygen Sensor (O2 Sensor) Mounting Nut
M12 x 1.25
1
Oxygen Sensor (O2 Sensor) Mounting Nut
M12 x 1.25
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
Estimated value based on similar components.
2 NOx Sensor Mounting Bolts
M8 x 1.25
2
NOx Sensor Mounting Bolts
M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Estimated value based on similar components.
3 DPF (Diesel Particulate Filter) Mounting Bolts
M10 x 1.25
3
DPF (Diesel Particulate Filter) Mounting Bolts
M10 x 1.25
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
Estimated value based on similar components.
4 Exhaust Gas Temperature Sensor Mounting Bolts
M8 x 1.25
4
Exhaust Gas Temperature Sensor Mounting Bolts
M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Estimated value based on similar components.
Egr System
1 EGR Valve Bolts
M8 x 1.25
1
EGR Valve Bolts
M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Ensure proper sealing to prevent exhaust leaks.
Exhaust
Torque specifications for Exhaust
Exhaust
Torque specifications for Exhaust
Exhaust Manifold Headers
1 Exhaust Manifold/Headers to Cylinder Head Bolts
M10 x 1.25
1
Exhaust Manifold/Headers to Cylinder Head Bolts
M10 x 1.25
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
Ensure bolts are tightened in a crisscross pattern to evenly distribute pressure.
2 Exhaust Pipe to Exhaust Manifold/Headers Bolts
M10 x 1.25
2
Exhaust Pipe to Exhaust Manifold/Headers Bolts
M10 x 1.25
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
Ensure a secure connection to prevent leaks at this critical junction.
Catalytic Converter
1 Catalytic Converter to Exhaust Pipe Bolts
M10 x 1.25
1
Catalytic Converter to Exhaust Pipe Bolts
M10 x 1.25
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
Ensure bolts are tightened evenly to avoid damaging the catalytic converter.
Muffler
1 Muffler to Exhaust Pipe Bolts
M10 x 1.25
1
Muffler to Exhaust Pipe Bolts
M10 x 1.25
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
Ensure a secure connection to prevent leaks and excessive noise.
Heat Shield
1 Exhaust Heat Shield Bolts
M6 x 1.0
1
Exhaust Heat Shield Bolts
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Estimated value based on typical heat shield bolt sizes. Avoid over-tightening to prevent damage.
Exhaust Hangers
1 Exhaust Hanger Bolts
M8 x 1.25
1
Exhaust Hanger Bolts
M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Ensure hangers are securely attached to prevent excessive movement of the exhaust system.
Oxygen Sensor
1 Oxygen Sensor (O2 Sensor) Mounting
M12 x 1.25
1
Oxygen Sensor (O2 Sensor) Mounting
M12 x 1.25
Torque Specification
33 ft-lbs (45 N·m)
Important Notes
Ensure the sensor is securely mounted to prevent leaks and ensure accurate readings.
Exhaust Flanges
1 Exhaust Flange Bolts (Downpipe to Midpipe)
M10 x 1.25
1
Exhaust Flange Bolts (Downpipe to Midpipe)
M10 x 1.25
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
Ensure a tight seal to prevent exhaust leaks at the flange connection.
Exhaust Clamps
1 Exhaust Clamp Bolts
M8 x 1.25
1
Exhaust Clamp Bolts
M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Avoid over-tightening to prevent crushing or damaging the exhaust pipes.
Fuel
Torque specifications for Fuel
Fuel
Torque specifications for Fuel
Fuel Rail System
1 Fuel Rail Bolts
M6 x 1.0
1
Fuel Rail Bolts
M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Ensure bolts are tightened in a crisscross pattern to evenly distribute pressure.
2 Fuel Injector Bolts
M6 x 1.0
2
Fuel Injector Bolts
M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Ensure injectors are properly seated before tightening bolts.
Fuel Delivery System
1 Fuel Pump Mounting Bolts
M8 x 1.25
1
Fuel Pump Mounting Bolts
M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Ensure the fuel pump is properly aligned before tightening bolts.
2 Fuel Tank Strap Bolts
M8 x 1.25
2
Fuel Tank Strap Bolts
M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Ensure the fuel tank is properly supported before tightening bolts.
3 Fuel Tank Sender Unit Bolts
M6 x 1.0
3
Fuel Tank Sender Unit Bolts
M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Ensure the sender unit is properly seated before tightening bolts.
Fuel Filtration System
1 Fuel Filter Bolt/Nut
M8 x 1.25
1
Fuel Filter Bolt/Nut
M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Ensure the fuel filter is properly aligned before tightening bolts.
Fuel Filler System
1 Fuel Filler Neck Bolts
M6 x 1.0
1
Fuel Filler Neck Bolts
M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Ensure the filler neck is properly aligned before tightening bolts.
High Pressure Fuel System
1 High-Pressure Fuel Pump Mounting Bolts
M8 x 1.25
1
High-Pressure Fuel Pump Mounting Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Estimated value based on similar components. Ensure the pump is properly aligned before tightening bolts.
2 Fuel Pressure Regulator Bolts
M6 x 1.0
2
Fuel Pressure Regulator Bolts
M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Ensure the regulator is properly seated before tightening bolts.
Fuel Line System
1 Fuel Line Flange Bolts
M6 x 1.0
1
Fuel Line Flange Bolts
M6 x 1.0
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Ensure the fuel line flanges are properly aligned before tightening bolts.
Hvac
Torque specifications for Hvac
Hvac
Torque specifications for Hvac
A/C Compressor
1 A/C Compressor Mounting Bolts
M12 x 1.5
1
A/C Compressor Mounting Bolts
M12 x 1.5
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Proper torque is essential to prevent damage to the compressor or surrounding components.
A/C Lines and Fittings
1 A/C Line Fittings
M10 x 1.25
1
A/C Line Fittings
M10 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Proper torque ensures a leak-free connection and prevents refrigerant leaks.
2 A/C Refrigerant Line Clamp Bolts
M8 x 1.25
2
A/C Refrigerant Line Clamp Bolts
M8 x 1.25
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Estimated value based on general industry standards. Proper torque ensures a leak-free connection and prevents refrigerant leaks.
A/C Condenser
1 A/C Condenser Mounting Bolts
M12 x 1.5
1
A/C Condenser Mounting Bolts
M12 x 1.5
Torque Specification
17 ft-lbs (23 N·m)
Important Notes
Estimated value based on general industry standards. Proper torque is essential to prevent damage to the condenser or surrounding components.
A/C Evaporator and Heater Core
1 A/C Evaporator Mounting Bolts
M10 x 1.25
1
A/C Evaporator Mounting Bolts
M10 x 1.25
Torque Specification
12 ft-lbs (16 N·m)
Important Notes
Estimated value based on general industry standards. Proper torque ensures proper airflow and prevents damage to the evaporator or surrounding components.
2 Heater Core Mounting Bolts
M10 x 1.25
2
Heater Core Mounting Bolts
M10 x 1.25
Torque Specification
12 ft-lbs (16 N·m)
Important Notes
Estimated value based on general industry standards. Proper torque ensures proper airflow and prevents damage to the heater core or surrounding components.
Suspension
Torque specifications for Suspension
Suspension
Torque specifications for Suspension
Strut Shock Absorber
1 Strut/Shock Absorber Mounting Bolts
M10 x 1.25
1
Strut/Shock Absorber Mounting Bolts
M10 x 1.25
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Ensure bolts are tightened evenly to prevent misalignment.
2 Lower Strut Mount Bolts
M12 x 1.5
2
Lower Strut Mount Bolts
M12 x 1.5
Torque Specification
52 ft-lbs (70 N·m)
Important Notes
Estimated value based on similar components.
3 Upper Strut Mount Bolts
M10 x 1.25
3
Upper Strut Mount Bolts
M10 x 1.25
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Ensure bolts are tightened evenly to prevent noise or misalignment.
Control Arm Ball Joint
1 Control Arm Bolts
M14 x 1.5
1
Control Arm Bolts
M14 x 1.5
Torque Specification
81 ft-lbs (110 N·m)
Important Notes
Ensure bolts are tightened evenly to prevent misalignment.
2 Ball Joint Nut
M12 x 1.25
2
Ball Joint Nut
M12 x 1.25
Torque Specification
52 ft-lbs (70 N·m)
Important Notes
Ensure the ball joint is properly seated before tightening.
Steering System
1 Tie Rod End Nut
M10 x 1.25
1
Tie Rod End Nut
M10 x 1.25
Torque Specification
33 ft-lbs (45 N·m)
Important Notes
Ensure the tie rod end is properly seated before tightening.
2 Steering Gear/Rack Bolts
M14 x 1.5
2
Steering Gear/Rack Bolts
M14 x 1.5
Torque Specification
81 ft-lbs (110 N·m)
Important Notes
Ensure bolts are tightened evenly to prevent steering play.
Sway Bar
1 Sway Bar Link Nut
M10 x 1.25
1
Sway Bar Link Nut
M10 x 1.25
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure the sway bar link is properly seated before tightening.
2 Rear Sway Bar Mounting Bolts
M10 x 1.25
2
Rear Sway Bar Mounting Bolts
M10 x 1.25
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure bolts are tightened evenly to prevent sway bar misalignment.
Drivetrain
1 Drive Axle/Half Shaft Bolts
M12 x 1.25
1
Drive Axle/Half Shaft Bolts
M12 x 1.25
Torque Specification
44 ft-lbs (60 N·m)
Important Notes
Ensure bolts are tightened evenly to prevent drivetrain vibration.
2 CV Joint/Axle Nut
M24 x 1.5
2
CV Joint/Axle Nut
M24 x 1.5
Torque Specification
181 ft-lbs (245 N·m)
Important Notes
Ensure the axle nut is properly seated before tightening.
Subframe
1 Subframe Mounting Bolts
M14 x 1.5
1
Subframe Mounting Bolts
M14 x 1.5
Torque Specification
1. 40 ft-lbs (54 N·m)
2. 81 ft-lbs (110 N·m)
Important Notes
Follow the torque sequence to ensure even clamping force.
Rear Suspension
1 Rear Suspension Trailing Arm Bolts
M14 x 1.5
1
Rear Suspension Trailing Arm Bolts
M14 x 1.5
Torque Specification
81 ft-lbs (110 N·m)
Important Notes
Ensure bolts are tightened evenly to prevent misalignment.
Troubleshooting Guide
Common issues, diagnostic steps, and prevention guidelines
Common Issues
Bolt stretching, stripped threads, uneven torque patterns
Common Issues
Bolt stretching, stripped threads, uneven torque patterns
Loose Components
Symptoms:
- Rattling or vibration noises
- Visible movement in components
- Uneven panel gaps
Solutions:
- Clean threads and mounting surfaces
- Replace damaged fasteners
- Apply proper torque in sequence
- Use thread locker if specified
Stripped Fasteners
Symptoms:
- Unable to achieve proper torque
- Fastener spins freely
- Visible thread damage
Solutions:
- Use thread repair kit if appropriate
- Install thread insert (HeliCoil)
- Replace component if threaded hole is damaged
- Upgrade to higher grade fastener if recommended
Overtightened Components
Symptoms:
- Cracked or deformed parts
- Broken fasteners
- Compressed gaskets or seals
Solutions:
- Replace damaged components
- Use new fasteners
- Follow proper torque sequence
- Verify correct torque specifications
Diagnostic Steps
Visual inspection, torque verification, thread assessment
Diagnostic Steps
Visual inspection, torque verification, thread assessment
1
Visual Inspection
Inspect the affected area for any visible signs of damage or wear
- Check for cracks or deformation
- Look for signs of excessive wear
- Verify proper fastener installation
2
Torque Verification
Verify the torque applied to the fasteners
- Check the torque wrench calibration
- Verify the torque specification
- Compare the applied torque to the specification
3
Thread Assessment
Assess the condition of the threads
- Check for signs of thread damage
- Verify the thread type and size
- Check for proper thread engagement
Prevention Guidelines
Best practices, maintenance tips, tool care
Prevention Guidelines
Best practices, maintenance tips, tool care
Best Practices
- Always follow the recommended torque specification
- Use the correct type and size of fasteners
- Verify the torque wrench calibration regularly
Maintenance Tips
- Regularly inspect the affected area for signs of wear or damage
- Replace damaged or worn-out components promptly
- Keep the work area clean and organized
Tool Care
- Regularly clean and maintain the torque wrench
- Store the torque wrench in a dry and secure location
- Verify the torque wrench calibration before each use
Frequently Asked Questions
Find answers to common questions about torque specifications
Q1 What IS the torque specification for the lug nuts on a 2018-Present Volkswagen Atlas?
Q1
What IS the torque specification for the lug nuts on a 2018-Present Volkswagen Atlas?
140 Nm (103 lb-ft) with a star pattern
Q2 What IS the proper tightening procedure for the cylinder head bolts on a 2018-Present Volkswagen Atlas?
Q2
What IS the proper tightening procedure for the cylinder head bolts on a 2018-Present Volkswagen Atlas?
Follow the Volkswagen specified tightening sequence and torque values listed in the service manual, using a calibrated torque wrench.
Q3 Can I use a generic torque wrench for all torque specifications on my 2018-Present Volkswagen Atlas?
Q3
Can I use a generic torque wrench for all torque specifications on my 2018-Present Volkswagen Atlas?
No, it IS recommended to use a torque wrench that IS calibrated to the specific torque values specified in the Volkswagen service manual.
Q4 How often should I check the torque on my 2018-Present Volkswagen Atlas?
Q4
How often should I check the torque on my 2018-Present Volkswagen Atlas?
Refer to the Volkswagen recommended maintenance schedule for specific torque check intervals.
Q5 What IS the torque specification for the oil filter on a 2018-Present Volkswagen Atlas?
Q5
What IS the torque specification for the oil filter on a 2018-Present Volkswagen Atlas?
25 Nm (18 lb-ft)
Q6 Can I use an impact wrench to tighten bolts on my 2018-Present Volkswagen Atlas?
Q6
Can I use an impact wrench to tighten bolts on my 2018-Present Volkswagen Atlas?
Impact wrenches should generally be avoided as they can over-tighten bolts and cause damage. Use a calibrated torque wrench instead.
Environmental Considerations
Temperature, humidity, and seasonal effects on torque specifications
Temperature Effects
Includes: High Heat, Cold Weather, Thermal Cycling
Temperature Effects
Includes: High Heat, Cold Weather, Thermal Cycling
Temperature can significantly impact torque values and fastener behavior
Cold Weather
Effects:
- Increased material brittleness
- Higher torque required due to thread contraction
- Reduced thread lubricant effectiveness
Recommendations:
- Allow components to warm to room temperature when possible
- Consider using winter-grade thread lubricants
- Check torque values more frequently during winter months
Hot Weather
Effects:
- Thermal expansion of components
- Decreased friction in threads
- Accelerated lubricant breakdown
Recommendations:
- Check torque when components are at normal operating temperature
- Use temperature-resistant thread lockers
- Consider re-torquing after heat cycles
Humidity and Corrosion
Covers: Rust Prevention, Salt Exposure, Moisture Control
Humidity and Corrosion
Covers: Rust Prevention, Salt Exposure, Moisture Control
Moisture and corrosion can affect fastener integrity and torque values
High Humidity
Effects:
- Accelerated corrosion formation
- Reduced friction coefficient
- Potential thread seizing
Prevention:
- Use corrosion-resistant fasteners
- Apply appropriate anti-seize compounds
- Maintain proper protective coatings
Salt Exposure
Effects:
- Rapid corrosion development
- Thread damage
- Seized fasteners
Prevention:
- Regular underbody washing
- Use of sacrificial anodes where appropriate
- Application of protective coatings
Seasonal Maintenance
Spring, Summer, Fall, and Winter maintenance schedules
Seasonal Maintenance
Spring, Summer, Fall, and Winter maintenance schedules
Spring
- Inspect for winter damage
- Clean and protect exposed fasteners
- Check torque on critical components
Summer
- Monitor heat-affected components
- Check expansion-related loosening
- Inspect cooling system mounts
Fall
- Prepare for winter conditions
- Apply corrosion protection
- Verify all fasteners are properly torqued
Winter
- More frequent inspection of critical fasteners
- Check for salt damage
- Monitor suspension component torque
Related Resources
Tools, service procedures, and technical bulletins
Recommended Tools
Digital Torque Wrench (10-100 Nm)
Essential for tightening fasteners to precise torque specifications, preventing damage and ensuring proper assembly. This range IS suitable for many applications on the atlas.
- Digital display for accurate readings
- Audible alarm when target torque IS reached
- Multiple units (Nm, ft-lb, in-lb)
- Reversible ratcheting mechanism
Service Procedures
Wheel Lug Nut Torque Specification
Properly torquing the wheel lug nuts IS crucial for ensuring safe and secure wheel attachment.
- Use a digital torque wrench to tighten the lug nuts to 140 Nm (103 ft-lb) in a star pattern.
- Recheck the torque after 50-100 km (30-60 miles) of driving, especially after installing new wheels or tires.
Engine Oil Drain Plug Torque Specification
Tightening the oil drain plug to the correct torque helps prevent leaks and ensure proper sealing.
- Clean the drain plug and the mating surface on the oil pan.
- Apply a light coating of oil to the threads of the drain plug.
- Tighten the drain plug to 30 Nm (22 ft-lb) using a torque wrench.
Spark Plug Torque Specification
Correctly torquing spark plugs IS crucial for ensuring proper ignition and engine performance.
- Clean the spark plug threads and the mating surface on the cylinder head.
- Apply a small amount of anti-seize compound to the threads of the spark plug.
- Hand-tighten the spark plug into the cylinder head.
- Use a torque wrench to tighten the spark plug to 28 Nm (21 ft-lb) for 1.4T engines and 30 Nm (22 ft-lb) for 2.0T and 3.6L engines.
Technical Service Bulletins
Technical Service Bulletin: Engine Oil Drain Plug Torque Specification Update
2022-03-01This bulletin revises the torque specification for the engine oil drain plug on 2018-2020 atlas models equipped with 1.4T and 2.0T engines.
2018-2020 Atlas with 1.4T and 2.0T engines
Resolution: Tighten the drain plug to 30 Nm (22 ft-lb) instead of the previously specified 25 Nm (18 ft-lb).
Technical Service Bulletin: Wheel Lug Nut Torque Specification Correction
2021-06-15This bulletin corrects the torque specification for the wheel lug nuts on 2018-2022 atlas models.
2018-2022 Atlas
Resolution: Tighten the lug nuts to 140 Nm (103 ft-lb) instead of the previously specified 120 Nm (89 ft-lb).
Legal Disclaimer
Important information about using this content
Always refer to your vehicle's service manual and take appropriate safety precautions when performing any maintenance or repairs.
General Information
The information provided on this website is for general informational purposes only. While we strive to maintain accuracy in our content, all specifications, procedures, and technical information should be verified against your vehicle's official service manual or with the manufacturer directly.
Warranty & Liability
The content on this website is provided "as is" without any representations or warranties, express or implied. We make no representations or warranties regarding the accuracy, completeness, or availability of the information.
We shall not be liable for any direct, indirect, special, or consequential damages arising from the use of information on this website.
Technical Information
- All specifications, including torque values, fluid capacities, and maintenance procedures, should be verified against your vehicle's factory service manual.
- Vehicle specifications and procedures may vary by model year, trim level, and region.
- Always follow the manufacturer's recommended procedures and safety precautions.
- Working on vehicles can be dangerous. Always take proper safety precautions and use appropriate safety equipment.
- If you're unsure about any procedure, consult a qualified professional mechanic.
Intellectual Property
All content, including text, images, and specifications, is protected by copyright and other intellectual property laws. Any unauthorized use or reproduction is prohibited.
About the Author
Expert automotive knowledge and experience
'/%3E%3Cpath d='M60 30a20 20 0 1 1 0 40 20 20 0 0 1 0-40zm0 45c16.5 0 30 7.5 30 16.8V100H30v-8.2c0-9.3 13.5-16.8 30-16.8z' fill='%23404040'/%3E%3C/svg%3E)
ASE
15+ Years
Experience
500+ Guides
Guides
50+ Makes
Vehicles
1000+ Solutions
Solutions
Diagnostic
Specialized in advanced diagnostic techniques using modern scan tools and oscilloscopes.
Repair
Expert in both traditional mechanical repairs and modern vehicle systems.
Additional Expertise
Documentation
Created over 500 detailed repair guides and technical documents.
Training
Conducted technical training sessions and contributed to repair databases.
Certifications & Research
Certifications
- ASE Master Technician Certification
- Advanced Diagnostic Specialist
- Hybrid/Electric Vehicle Systems
- Performance Tuning Expert
Research & Community
Actively researches emerging technologies and contributes to automotive forums.