Volkswagen Vehicle Models Volkswagen Golf 2020-present
Volkswagen Vehicle Models Volkswagen Golf 2020-present Torque Specifications
Complete Volkswagen Vehicle Models Volkswagen Golf 2020-present torque specifications guide. Includes factory-specified torque values, torque sequences, and technical specifications for all components including body, brakes, drivetrain, electrical, emissions sensors, fuel, exhaust, HVAC, and suspension. Essential information for proper assembly and maintenance.
Updated
Important Information
Safety guidelines and reference information for proper torque application
Safety First
- Always verify torque specifications with your vehicle's factory service manual
- Use properly calibrated torque wrenches
- Replace all torque-to-yield (TTY) bolts - they are single-use only
- When in doubt, consult a professional mechanic
Quick Reference Guide
Quick Reference Guide
ft-lbs → Nm
× 1.356
ft-lbs → kg-m
× 0.138
Nm → ft-lbs
× 0.738
in-lbs → ft-lbs
× 0.083
Common Torque Patterns
Star Pattern
Used for wheels and other circular bolt patterns
Cross Pattern
Used for gaskets and cover plates
Sequential Pattern
Used for head bolts and other critical components
Common Mistakes to Avoid
Common Mistakes to Avoid
Over-tightening
Exceeding the specified torque value can stretch or break fasteners, damage threads, or crack components.
Prevention:
Always use a calibrated torque wrench and follow specifications exactly.
Incorrect Torque Sequence
Tightening bolts in the wrong order can cause uneven pressure distribution and potential leaks or damage.
Prevention:
Follow the manufacturer's specified torque sequence pattern.
Dirty Threads
Dirt, rust, or old thread locker can affect torque readings and proper fastener tension.
Prevention:
Clean and inspect all threads before assembly. Use new thread locker if specified.
Reusing TTY Bolts
Torque-to-yield bolts are designed to stretch and must not be reused.
Prevention:
Always replace TTY bolts with new ones. They are single-use only.
Dry vs. Lubricated
Not accounting for whether torque specs are for dry or lubricated fasteners can lead to incorrect tension.
Prevention:
Check if specs are for dry or lubricated threads. Use specified lubricant when required.
Recommended Tools
Recommended Tools
Torque Wrench (1/4" Drive)
Range: 2-25 ft-lbs
Small fasteners, delicate components
Torque Wrench (3/8" Drive)
Range: 10-100 ft-lbs
Most common automotive fasteners
Torque Wrench (1/2" Drive)
Range: 30-250 ft-lbs
Large fasteners, wheels
Angle Gauge
Torque-to-yield (TTY) bolts
Torque Wrench Care
- Calibrate annually or after 5,000 clicks
- Store at lowest setting
- Keep clean and lubricated
Search Specifications
Search by component name, bolt size, or description
Type to search through torque specifications. Use arrow keys to navigate results. Press Enter to select a result.
Torque Calculator
Convert between different torque units
1.0l I3 Engine
Torque specifications for 1.0L-I3 Engine
1.0l I3 Engine
Torque specifications for 1.0L-I3 Engine
Cylinder Head
1 Cylinder Head Bolts
M10 x 1.25
1
Cylinder Head Bolts
M10 x 1.25
Torque Specification
1. 18 ft-lbs (25 N·m)
2. 90°
Important Notes
Follow the manufacturer's torque sequence for proper sealing. Estimated bolt size based on typical cylinder head bolts.
Crankshaft And Bearings
1 Main Bearing Bolts
M12 x 1.5
1
Main Bearing Bolts
M12 x 1.5
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Ensure proper alignment of the crankshaft before tightening. Estimated bolt size based on typical main bearing bolts.
2 Connecting Rod Nuts
M8 x 1.0
2
Connecting Rod Nuts
M8 x 1.0
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Ensure proper alignment of the connecting rods. Estimated bolt size based on typical connecting rod nuts.
Flywheel And Clutch
1 Flywheel Bolts
M10 x 1.25
1
Flywheel Bolts
M10 x 1.25
Torque Specification
44 ft-lbs (60 N·m)
Important Notes
Ensure proper alignment of the flywheel. Estimated bolt size based on typical flywheel bolts.
Oil System
1 Oil Pan Bolts
M6 x 1.0
1
Oil Pan Bolts
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure proper sealing of the oil pan gasket. Estimated bolt size based on typical oil pan bolts.
2 Oil Drain Plug
M14 x 1.5
2
Oil Drain Plug
M14 x 1.5
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Replace the crush washer during installation. Estimated bolt size based on typical oil drain plugs.
Valvetrain
1 Valve Cover Bolts
M6 x 1.0
1
Valve Cover Bolts
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure proper sealing of the valve cover gasket. Estimated bolt size based on typical valve cover bolts.
2 Camshaft Sprocket Bolt
M8 x 1.25
2
Camshaft Sprocket Bolt
M8 x 1.25
Torque Specification
21 ft-lbs (28 N·m)
Important Notes
Ensure proper alignment of the camshaft sprocket. Estimated bolt size based on typical camshaft sprocket bolts.
Turbocharger System
1 Turbocharger Mounting Bolts
M8 x 1.25
1
Turbocharger Mounting Bolts
M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Ensure proper alignment of the turbocharger. Estimated bolt size based on typical turbocharger mounting bolts.
2 Turbocharger Oil Feed Line Bolts
M6 x 1.0
2
Turbocharger Oil Feed Line Bolts
M6 x 1.0
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Ensure proper sealing of the oil feed line. Estimated bolt size based on typical oil line bolts.
1.0l I3 Turbo Engine
Torque specifications for 1.0L-I3-TURBO Engine
1.0l I3 Turbo Engine
Torque specifications for 1.0L-I3-TURBO Engine
Cylinder Head
1 Cylinder Head Bolts
M10 x 1.25
1
Cylinder Head Bolts
M10 x 1.25
Torque Specification
1. 18 ft-lbs (25 N·m)
2. 90°
Important Notes
Follow the manufacturer's torque sequence for proper sealing. Estimated bolt size based on typical cylinder head bolts.
Crankshaft And Bearings
1 Main Bearing Bolts
M12 x 1.5
1
Main Bearing Bolts
M12 x 1.5
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Ensure proper alignment of the crankshaft before tightening. Estimated bolt size based on typical main bearing bolts.
2 Connecting Rod Nuts
M8 x 1.0
2
Connecting Rod Nuts
M8 x 1.0
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Ensure proper alignment of the connecting rods. Estimated bolt size based on typical connecting rod nuts.
Flywheel And Clutch
1 Flywheel Bolts
M10 x 1.25
1
Flywheel Bolts
M10 x 1.25
Torque Specification
44 ft-lbs (60 N·m)
Important Notes
Ensure proper alignment of the flywheel. Estimated bolt size based on typical flywheel bolts.
Oil System
1 Oil Pan Bolts
M6 x 1.0
1
Oil Pan Bolts
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure proper sealing of the oil pan gasket. Estimated bolt size based on typical oil pan bolts.
2 Oil Drain Plug
M14 x 1.5
2
Oil Drain Plug
M14 x 1.5
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Replace the crush washer during installation. Estimated bolt size based on typical oil drain plugs.
Valvetrain
1 Valve Cover Bolts
M6 x 1.0
1
Valve Cover Bolts
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure proper sealing of the valve cover gasket. Estimated bolt size based on typical valve cover bolts.
2 Camshaft Sprocket Bolt
M8 x 1.25
2
Camshaft Sprocket Bolt
M8 x 1.25
Torque Specification
21 ft-lbs (28 N·m)
Important Notes
Ensure proper alignment of the camshaft sprocket. Estimated bolt size based on typical camshaft sprocket bolts.
Turbocharger System
1 Turbocharger Mounting Bolts
M8 x 1.25
1
Turbocharger Mounting Bolts
M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Ensure proper alignment of the turbocharger. Estimated bolt size based on typical turbocharger mounting bolts.
2 Turbocharger Oil Feed Line Bolts
M6 x 1.0
2
Turbocharger Oil Feed Line Bolts
M6 x 1.0
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Ensure proper sealing of the oil feed line. Estimated bolt size based on typical oil line bolts.
1.5l I4 Engine
Torque specifications for 1.5L-I4 Engine
1.5l I4 Engine
Torque specifications for 1.5L-I4 Engine
Cylinder Head
1 Cylinder Head Bolts
M10 x 1.25
1
Cylinder Head Bolts
M10 x 1.25
Torque Specification
1. 18 ft-lbs (25 N·m)
2. 90°
Important Notes
Follow the manufacturer's specified torque sequence to ensure even clamping force.
2 Valve Cover Bolts
M6 x 1.0
2
Valve Cover Bolts
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure the valve cover gasket is properly seated before tightening.
Crankshaft And Bearings
1 Main Bearing Bolts
M10 x 1.25
1
Main Bearing Bolts
M10 x 1.25
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Ensure the crankshaft is properly seated before tightening.
2 Connecting Rod Nuts
M8 x 1.0
2
Connecting Rod Nuts
M8 x 1.0
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Ensure the connecting rod bearings are properly installed.
Timing System
1 Timing Belt/Chain Tensioner Bolt
M8 x 1.25
1
Timing Belt/Chain Tensioner Bolt
M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Ensure the tensioner is properly aligned before tightening.
2 Camshaft Sprocket Bolt
M10 x 1.25
2
Camshaft Sprocket Bolt
M10 x 1.25
Torque Specification
21 ft-lbs (28 N·m)
Important Notes
Ensure the camshaft is properly timed before tightening.
Turbocharger System
1 Turbocharger Mounting Bolts
M8 x 1.25
1
Turbocharger Mounting Bolts
M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Estimated value based on similar turbocharger systems.
2 Turbocharger Oil Feed Line Bolt
M6 x 1.0
2
Turbocharger Oil Feed Line Bolt
M6 x 1.0
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Estimated value based on similar oil line connections.
Accessory Drives
1 Alternator Mounting Bolts
M8 x 1.25
1
Alternator Mounting Bolts
M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Ensure the alternator is properly aligned before tightening.
2 A/C Compressor Mounting Bolts
M10 x 1.25
2
A/C Compressor Mounting Bolts
M10 x 1.25
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
Ensure the A/C compressor is properly aligned before tightening.
1.5l I4 Turbo Engine
Torque specifications for 1.5L-I4-TURBO Engine
1.5l I4 Turbo Engine
Torque specifications for 1.5L-I4-TURBO Engine
Cylinder Head
1 Cylinder Head Bolts
M10 x 1.25
1
Cylinder Head Bolts
M10 x 1.25
Torque Specification
1. 18 ft-lbs (25 N·m)
2. 90°
Important Notes
Follow the manufacturer's specified torque sequence to ensure even clamping force.
2 Valve Cover Bolts
M6 x 1.0
2
Valve Cover Bolts
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure the valve cover gasket is properly seated before tightening.
Crankshaft And Bearings
1 Main Bearing Bolts
M10 x 1.25
1
Main Bearing Bolts
M10 x 1.25
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Ensure the crankshaft is properly seated before tightening.
2 Connecting Rod Nuts
M8 x 1.0
2
Connecting Rod Nuts
M8 x 1.0
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Ensure the connecting rod bearings are properly installed.
Timing System
1 Timing Belt/Chain Tensioner Bolt
M8 x 1.25
1
Timing Belt/Chain Tensioner Bolt
M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Ensure the tensioner is properly aligned before tightening.
2 Camshaft Sprocket Bolt
M10 x 1.25
2
Camshaft Sprocket Bolt
M10 x 1.25
Torque Specification
21 ft-lbs (28 N·m)
Important Notes
Ensure the camshaft is properly timed before tightening.
Turbocharger System
1 Turbocharger Mounting Bolts
M8 x 1.25
1
Turbocharger Mounting Bolts
M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Estimated value based on similar turbocharger systems.
2 Turbocharger Oil Feed Line Bolt
M6 x 1.0
2
Turbocharger Oil Feed Line Bolt
M6 x 1.0
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Estimated value based on similar oil line connections.
Accessory Drives
1 Alternator Mounting Bolts
M8 x 1.25
1
Alternator Mounting Bolts
M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Ensure the alternator is properly aligned before tightening.
2 A/C Compressor Mounting Bolts
M10 x 1.25
2
A/C Compressor Mounting Bolts
M10 x 1.25
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
Ensure the A/C compressor is properly aligned before tightening.
2.0l I4 Engine
Torque specifications for 2.0L-I4 Engine
2.0l I4 Engine
Torque specifications for 2.0L-I4 Engine
Cylinder Head
1 Cylinder Head Bolts
M10 x 1.5
1
Cylinder Head Bolts
M10 x 1.5
Torque Specification
1. 18 ft-lbs (25 N·m)
2. 90°
Important Notes
Follow the manufacturer's specified torque sequence for the cylinder head bolts.
2 Valve Cover Bolts
M6 x 1.0
2
Valve Cover Bolts
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure the valve cover gasket is properly seated before tightening.
Crankshaft And Bearings
1 Main Bearing Bolts
M10 x 1.25
1
Main Bearing Bolts
M10 x 1.25
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Ensure the bearing caps are properly aligned before tightening.
2 Connecting Rod Nuts
M8 x 1.0
2
Connecting Rod Nuts
M8 x 1.0
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Ensure the connecting rod bearings are properly seated.
3 Flywheel Bolts
M12 x 1.5
3
Flywheel Bolts
M12 x 1.5
Torque Specification
44 ft-lbs (60 N·m)
Important Notes
Use thread locker on the flywheel bolts.
Timing System
1 Timing Belt/Chain Tensioner Bolt
M8 x 1.25
1
Timing Belt/Chain Tensioner Bolt
M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Ensure the tensioner is properly aligned before tightening.
2 Camshaft Sprocket Bolt
M10 x 1.25
2
Camshaft Sprocket Bolt
M10 x 1.25
Torque Specification
21 ft-lbs (28 N·m)
Important Notes
Ensure the camshaft is properly aligned before tightening.
Turbocharger System
1 Turbocharger Mounting Bolts
M8 x 1.25
1
Turbocharger Mounting Bolts
M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Ensure the turbocharger is properly aligned before tightening.
2 Turbocharger Oil Feed Line Bolts
M6 x 1.0
2
Turbocharger Oil Feed Line Bolts
M6 x 1.0
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Ensure the oil feed line is properly seated.
3 Turbocharger Exhaust Flange Bolts
M8 x 1.25
3
Turbocharger Exhaust Flange Bolts
M8 x 1.25
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Ensure the exhaust flange is properly aligned.
Fuel System
1 Fuel Rail Bolts
M6 x 1.0
1
Fuel Rail Bolts
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure the fuel rail is properly seated.
2 High-Pressure Fuel Pump Bolts
M8 x 1.25
2
High-Pressure Fuel Pump Bolts
M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Ensure the pump is properly aligned before tightening.
2.0l I4 Turbo Engine
Torque specifications for 2.0L-I4-TURBO Engine
2.0l I4 Turbo Engine
Torque specifications for 2.0L-I4-TURBO Engine
Cylinder Head
1 Cylinder Head Bolts
M10 x 1.5
1
Cylinder Head Bolts
M10 x 1.5
Torque Specification
1. 18 ft-lbs (25 N·m)
2. 90°
Important Notes
Follow the manufacturer's specified torque sequence for the cylinder head bolts.
2 Valve Cover Bolts
M6 x 1.0
2
Valve Cover Bolts
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure the valve cover gasket is properly seated before tightening.
Crankshaft And Bearings
1 Main Bearing Bolts
M10 x 1.25
1
Main Bearing Bolts
M10 x 1.25
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Ensure the bearing caps are properly aligned before tightening.
2 Connecting Rod Nuts
M8 x 1.0
2
Connecting Rod Nuts
M8 x 1.0
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Ensure the connecting rod bearings are properly seated.
3 Flywheel Bolts
M12 x 1.5
3
Flywheel Bolts
M12 x 1.5
Torque Specification
44 ft-lbs (60 N·m)
Important Notes
Use thread locker on the flywheel bolts.
Timing System
1 Timing Belt/Chain Tensioner Bolt
M8 x 1.25
1
Timing Belt/Chain Tensioner Bolt
M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Ensure the tensioner is properly aligned before tightening.
2 Camshaft Sprocket Bolt
M10 x 1.25
2
Camshaft Sprocket Bolt
M10 x 1.25
Torque Specification
21 ft-lbs (28 N·m)
Important Notes
Ensure the camshaft is properly aligned before tightening.
Turbocharger System
1 Turbocharger Mounting Bolts
M8 x 1.25
1
Turbocharger Mounting Bolts
M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Ensure the turbocharger is properly aligned before tightening.
2 Turbocharger Oil Feed Line Bolts
M6 x 1.0
2
Turbocharger Oil Feed Line Bolts
M6 x 1.0
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Ensure the oil feed line is properly seated.
3 Turbocharger Exhaust Flange Bolts
M8 x 1.25
3
Turbocharger Exhaust Flange Bolts
M8 x 1.25
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Ensure the exhaust flange is properly aligned.
Fuel System
1 Fuel Rail Bolts
M6 x 1.0
1
Fuel Rail Bolts
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure the fuel rail is properly seated.
2 High-Pressure Fuel Pump Bolts
M8 x 1.25
2
High-Pressure Fuel Pump Bolts
M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Ensure the pump is properly aligned before tightening.
Body
Torque specifications for Body
Body
Torque specifications for Body
Suspension And Steering
1 Wheel Lug Nuts
M12 x 1.5
1
Wheel Lug Nuts
M12 x 1.5
Torque Specification
89 ft-lbs (120 N·m)
Important Notes
Critical for safety. Always tighten in a star pattern.
2 Strut/Shock Absorber Mounting Bolts
M10 x 1.25
2
Strut/Shock Absorber Mounting Bolts
M10 x 1.25
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
Ensure proper alignment of suspension components.
3 Control Arm Bolts
M14 x 1.5
3
Control Arm Bolts
M14 x 1.5
Torque Specification
85 ft-lbs (115 N·m)
Important Notes
Critical for suspension geometry and handling.
4 Ball Joint Nut
M12 x 1.25
4
Ball Joint Nut
M12 x 1.25
Torque Specification
52 ft-lbs (70 N·m)
Important Notes
Ensure proper steering and suspension operation.
5 Tie Rod End Nut
M10 x 1.25
5
Tie Rod End Nut
M10 x 1.25
Torque Specification
33 ft-lbs (45 N·m)
Important Notes
Critical for steering alignment and control.
6 Sway Bar Link Nut
M10 x 1.25
6
Sway Bar Link Nut
M10 x 1.25
Torque Specification
33 ft-lbs (45 N·m)
Important Notes
Ensures stability and reduces body roll.
7 Steering Gear/Rack Bolts
M12 x 1.5
7
Steering Gear/Rack Bolts
M12 x 1.5
Torque Specification
59 ft-lbs (80 N·m)
Important Notes
Critical for safe and accurate steering operation.
Fuel System
1 Fuel Tank Strap Bolts
M8 x 1.25
1
Fuel Tank Strap Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensures the fuel tank remains securely mounted.
2 Fuel Filler Neck Bolts
M6 x 1.0
2
Fuel Filler Neck Bolts
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensures a secure connection and prevents fuel leaks.
Electrical System
1 Battery Terminal Nuts
M6 x 1.0
1
Battery Terminal Nuts
M6 x 1.0
Torque Specification
5 ft-lbs (7 N·m)
Important Notes
Ensures a reliable electrical connection and prevents corrosion.
Body Structure
1 Door Hinge Bolts
M8 x 1.25
1
Door Hinge Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensures proper door alignment and operation.
2 Seat Mounting Bolts
M10 x 1.25
2
Seat Mounting Bolts
M10 x 1.25
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Critical for passenger safety and seat stability.
3 Hood Hinge Bolts
M8 x 1.25
3
Hood Hinge Bolts
M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Ensures proper hood alignment and operation.
4 Trunk Lid Hinge Bolts
M8 x 1.25
4
Trunk Lid Hinge Bolts
M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Ensures proper trunk lid alignment and operation.
5 Bumper Mounting Bolts
M8 x 1.25
5
Bumper Mounting Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensures bumper remains securely attached and aligned.
6 Roof Rack Mounting Bolts
M8 x 1.25
6
Roof Rack Mounting Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensures roof rack remains securely attached during use.
Brakes
Torque specifications for Brakes
Brakes
Torque specifications for Brakes
Brake Caliper
1 Brake Caliper Bolts
M10 x 1.25
1
Brake Caliper Bolts
M10 x 1.25
Torque Specification
59 ft-lbs (80 N·m)
Important Notes
Ensure the caliper is properly aligned before torquing.
2 Brake Caliper Mounting Bracket Bolts
M12 x 1.5
2
Brake Caliper Mounting Bracket Bolts
M12 x 1.5
Torque Specification
81 ft-lbs (110 N·m)
Important Notes
Ensure the bracket is securely attached to the steering knuckle or axle.
Brake Rotor
1 Brake Disc/Drum Retaining Bolts
M12 x 1.5
1
Brake Disc/Drum Retaining Bolts
M12 x 1.5
Torque Specification
81 ft-lbs (110 N·m)
Important Notes
Ensure the rotor is properly seated on the hub before torquing.
Wheel Assembly
1 Wheel Lug Nuts
M14 x 1.5
1
Wheel Lug Nuts
M14 x 1.5
Torque Specification
89 ft-lbs (120 N·m)
Important Notes
Always use a star pattern when tightening lug nuts to ensure even pressure.
Brake Hydraulics
1 Brake Hose Banjo Bolt
M10 x 1.0
1
Brake Hose Banjo Bolt
M10 x 1.0
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Ensure the banjo bolt is properly aligned with the brake hose.
2 Brake Master Cylinder Mounting Bolts
M8 x 1.25
2
Brake Master Cylinder Mounting Bolts
M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Ensure the master cylinder is properly aligned with the brake booster.
Brake Pedal
1 Brake Pedal Assembly Bolts
M8 x 1.25
1
Brake Pedal Assembly Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure the pedal assembly is properly aligned with the master cylinder.
Abs System
1 ABS Sensor Mounting Bolts
M6 x 1.0
1
ABS Sensor Mounting Bolts
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure the ABS sensor is properly aligned with the wheel hub.
Drivetrain
Torque specifications for Drivetrain
Drivetrain
Torque specifications for Drivetrain
Engine And Flywheel
1 Flywheel Bolts
M10 x 1.25
1
Flywheel Bolts
M10 x 1.25
Torque Specification
44 ft-lbs (60 N·m)
Important Notes
Critical for securing the flywheel to the crankshaft. Torque in a star pattern.
2 Crankshaft Pulley/Harmonic Balancer Bolt
M12 x 1.5
2
Crankshaft Pulley/Harmonic Balancer Bolt
M12 x 1.5
Torque Specification
81 ft-lbs (110 N·m)
Important Notes
Ensures proper alignment and balance of the drivetrain.
3 Clutch Pressure Plate Bolts
M8 x 1.25
3
Clutch Pressure Plate Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensures smooth clutch operation. Torque in a star pattern.
Transmission And Mounts
1 Transmission Mounting Bolts
M10 x 1.25
1
Transmission Mounting Bolts
M10 x 1.25
Torque Specification
44 ft-lbs (60 N·m)
Important Notes
Ensures the transmission remains stable and properly aligned.
2 Transmission Bellhousing Bolts
M10 x 1.25
2
Transmission Bellhousing Bolts
M10 x 1.25
Torque Specification
59 ft-lbs (80 N·m)
Important Notes
Ensures proper alignment between the transmission and engine.
3 Transmission Oil Pan Bolts
M6 x 1.0
3
Transmission Oil Pan Bolts
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Prevents leaks and ensures the integrity of the transmission lubrication system.
Driveshaft And Axles
1 Drive Axle/Half Shaft Bolts
M12 x 1.5
1
Drive Axle/Half Shaft Bolts
M12 x 1.5
Torque Specification
81 ft-lbs (110 N·m)
Important Notes
Ensures the axles remain securely attached to the transmission or differential.
2 CV Joint/Axle Nut
M24 x 1.5
2
CV Joint/Axle Nut
M24 x 1.5
Torque Specification
111 ft-lbs (150 N·m)
Important Notes
Ensures the CV joint remains securely attached to the wheel hub.
3 Propeller/Drive Shaft Bolts
M12 x 1.5
3
Propeller/Drive Shaft Bolts
M12 x 1.5
Torque Specification
81 ft-lbs (110 N·m)
Important Notes
Ensures the driveshaft remains securely attached to the transmission and differential.
4 Rear Axle Hub Bolts
M12 x 1.5
4
Rear Axle Hub Bolts
M12 x 1.5
Torque Specification
81 ft-lbs (110 N·m)
Important Notes
Ensures the rear axle hub remains securely attached to the differential.
Differential And Transfer Case
1 Differential Mounting Bolts
M10 x 1.25
1
Differential Mounting Bolts
M10 x 1.25
Torque Specification
59 ft-lbs (80 N·m)
Important Notes
Ensures the differential remains stable and properly aligned with the drivetrain.
2 Transfer Case Mounting Bolts
M10 x 1.25
2
Transfer Case Mounting Bolts
M10 x 1.25
Torque Specification
59 ft-lbs (80 N·m)
Important Notes
Ensures the transfer case remains stable and properly aligned with the drivetrain.
3 Differential Drain/Fill Plug
M12 x 1.5
3
Differential Drain/Fill Plug
M12 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensures the differential fluid system remains sealed.
4 Transfer Case Drain/Fill Plug
M12 x 1.5
4
Transfer Case Drain/Fill Plug
M12 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensures the transfer case fluid system remains sealed.
Transmission Fluid System
1 Transmission Drain and Fill Plugs
M12 x 1.5
1
Transmission Drain and Fill Plugs
M12 x 1.5
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Ensures the transmission fluid system remains sealed.
Dsg7 Transmission
Torque specifications for Dsg7 Transmission
Dsg7 Transmission
Torque specifications for Dsg7 Transmission
Flywheel And Bellhousing
1 Flywheel Bolts
M10 x 1.25
1
Flywheel Bolts
M10 x 1.25
Torque Specification
44 ft-lbs (60 N·m)
Important Notes
Ensure proper alignment of the flywheel before tightening. Use a crisscross pattern for even torque distribution.
2 Transmission Bellhousing Bolts
M10 x 1.25
2
Transmission Bellhousing Bolts
M10 x 1.25
Torque Specification
44 ft-lbs (60 N·m)
Important Notes
Ensure proper alignment of the bellhousing before tightening. Use a crisscross pattern for even torque distribution.
Transmission Mounting
1 Transmission Mounting Bolts
M10 x 1.25
1
Transmission Mounting Bolts
M10 x 1.25
Torque Specification
44 ft-lbs (60 N·m)
Important Notes
Ensure proper alignment of the transmission before tightening. Use a crisscross pattern for even torque distribution.
Oil Pan And Plugs
1 Transmission Oil Pan Bolts
M6 x 1.0
1
Transmission Oil Pan Bolts
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure the oil pan gasket is properly seated before tightening. Use a crisscross pattern for even torque distribution.
2 Transmission Drain Plug
M14 x 1.5
2
Transmission Drain Plug
M14 x 1.5
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Ensure the drain plug sealing washer is in good condition before installation.
3 Transmission Fill Plug
M14 x 1.5
3
Transmission Fill Plug
M14 x 1.5
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Ensure the fill plug sealing washer is in good condition before installation.
Driveline Components
1 Drive Axle/Half Shaft Bolts
M12 x 1.5
1
Drive Axle/Half Shaft Bolts
M12 x 1.5
Torque Specification
81 ft-lbs (110 N·m)
Important Notes
Ensure proper alignment of the drive axle before tightening. Use a crisscross pattern for even torque distribution.
2 CV Joint/Axle Nut
M24 x 1.5
2
CV Joint/Axle Nut
M24 x 1.5
Torque Specification
111 ft-lbs (150 N·m)
Important Notes
Ensure the CV joint is properly seated before tightening.
3 Propeller/Drive Shaft Bolts
M12 x 1.5
3
Propeller/Drive Shaft Bolts
M12 x 1.5
Torque Specification
81 ft-lbs (110 N·m)
Important Notes
Ensure proper alignment of the propeller shaft before tightening. Use a crisscross pattern for even torque distribution.
Mechatronic Unit
1 Mechatronic Unit Bolts
M6 x 1.0
1
Mechatronic Unit Bolts
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure proper alignment of the mechatronic unit before tightening. Use a crisscross pattern for even torque distribution.
Clutch Pack
1 Clutch Pack Bolts
M8 x 1.25
1
Clutch Pack Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure proper alignment of the clutch pack before tightening. Use a crisscross pattern for even torque distribution.
Shift Linkage
1 Transmission Shift Linkage Bolts
M6 x 1.0
1
Transmission Shift Linkage Bolts
M6 x 1.0
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Ensure proper alignment of the shift linkage before tightening. Use a crisscross pattern for even torque distribution.
Cooler Lines
1 Transmission Cooler Line Fittings
M12 x 1.5
1
Transmission Cooler Line Fittings
M12 x 1.5
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Ensure the cooler line fittings are properly aligned before tightening.
Electrical
Torque specifications for Electrical
Electrical
Torque specifications for Electrical
Starter Motor
1 Starter Motor Mounting Bolts
M10 x 1.25
1
Starter Motor Mounting Bolts
M10 x 1.25
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure proper alignment with the engine block before tightening.
Alternator
1 Alternator Mounting Bolts
M8 x 1.25
1
Alternator Mounting Bolts
M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Ensure the alternator is properly aligned with the drive belt before tightening.
Battery
1 Battery Terminal Nuts
M6 x 1.0
1
Battery Terminal Nuts
M6 x 1.0
Torque Specification
5 ft-lbs (7 N·m)
Important Notes
Avoid overtightening to prevent damage to the battery terminals.
Ignition System
1 Ignition Coil Bolt
M6 x 1.0
1
Ignition Coil Bolt
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure the ignition coil is properly seated on the cylinder head.
Ac System
1 A/C Compressor Mounting Bolts
M10 x 1.25
1
A/C Compressor Mounting Bolts
M10 x 1.25
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
Ensure proper alignment with the drive belt before tightening.
2 A/C Line Fittings
M8 x 1.25
2
A/C Line Fittings
M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Ensure fittings are clean and free of debris before tightening.
Grounding System
1 Ground Strap Bolts
M6 x 1.0
1
Ground Strap Bolts
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Estimated value based on similar grounding components.
Fuse Box
1 Fuse Box Mounting Bolts
M6 x 1.0
1
Fuse Box Mounting Bolts
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Estimated value based on similar electrical components.
Ecu
1 ECU Mounting Bolts
M6 x 1.0
1
ECU Mounting Bolts
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Estimated value based on similar electrical components.
Wiring Harness
1 Wiring Harness Retaining Bolts
M6 x 1.0
1
Wiring Harness Retaining Bolts
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Estimated value based on similar electrical components.
Eps
1 EPS Mounting Bolts
M10 x 1.25
1
EPS Mounting Bolts
M10 x 1.25
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
Estimated value based on similar steering components.
Emissions Sensors
Torque specifications for Emissions_sensors
Emissions Sensors
Torque specifications for Emissions_sensors
Egr System
1 EGR Valve Bolts
M6 x 1.0
1
EGR Valve Bolts
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure the EGR valve is properly aligned before tightening.
Exhaust Manifold
1 Exhaust Manifold/Headers Bolts
M8 x 1.25
1
Exhaust Manifold/Headers Bolts
M8 x 1.25
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Use a crisscross pattern to ensure even pressure distribution.
2 Exhaust Manifold/Headers to Cylinder Head Bolts
M8 x 1.25
2
Exhaust Manifold/Headers to Cylinder Head Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure the manifold is properly aligned before tightening.
Exhaust Pipe
1 Exhaust Pipe to Exhaust Manifold/Headers Bolts
M8 x 1.25
1
Exhaust Pipe to Exhaust Manifold/Headers Bolts
M8 x 1.25
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Ensure the gasket is properly seated before tightening.
2 Catalytic Converter to Exhaust Pipe Bolts
M8 x 1.25
2
Catalytic Converter to Exhaust Pipe Bolts
M8 x 1.25
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Ensure the gasket is properly seated before tightening.
Emissions Sensors
1 Oxygen Sensor (Lambda Sensor)
M12 x 1.5
1
Oxygen Sensor (Lambda Sensor)
M12 x 1.5
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
Estimated value based on similar sensor applications.
2 NOx Sensor Bolts
M6 x 1.0
2
NOx Sensor Bolts
M6 x 1.0
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Estimated value based on similar sensor applications.
Diesel Particulate Filter
1 DPF Mounting Bolts
M8 x 1.25
1
DPF Mounting Bolts
M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Estimated value based on similar filter applications.
Secondary Air Injection
1 Secondary Air Injection System Bolts
M6 x 1.0
1
Secondary Air Injection System Bolts
M6 x 1.0
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Estimated value based on similar system applications.
Exhaust
Torque specifications for Exhaust
Exhaust
Torque specifications for Exhaust
Exhaust Manifold Headers
1 Exhaust Manifold/Headers to Cylinder Head Bolts
M8 x 1.25
1
Exhaust Manifold/Headers to Cylinder Head Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure bolts are tightened in a crisscross pattern to evenly distribute pressure.
2 Exhaust Pipe to Exhaust Manifold/Headers Bolts
M10 x 1.5
2
Exhaust Pipe to Exhaust Manifold/Headers Bolts
M10 x 1.5
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Ensure gasket is properly seated before tightening.
Catalytic Converter
1 Catalytic Converter to Exhaust Pipe Bolts
M10 x 1.5
1
Catalytic Converter to Exhaust Pipe Bolts
M10 x 1.5
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Use a new gasket to ensure a proper seal.
Muffler
1 Muffler to Exhaust Pipe Bolts
M10 x 1.5
1
Muffler to Exhaust Pipe Bolts
M10 x 1.5
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Ensure gasket is properly seated before tightening.
Oxygen Sensor
1 Oxygen Sensor (O2 Sensor) Mounting Bolt
M12 x 1.5
1
Oxygen Sensor (O2 Sensor) Mounting Bolt
M12 x 1.5
Torque Specification
33 ft-lbs (45 N·m)
Important Notes
Ensure the sensor is properly aligned before tightening.
Heat Shield
1 Exhaust Heat Shield Bolts
M6 x 1.0
1
Exhaust Heat Shield Bolts
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Avoid over-tightening to prevent damage to the heat shield.
Exhaust Hanger
1 Exhaust Hanger Bolts
M8 x 1.25
1
Exhaust Hanger Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure hangers are properly aligned before tightening.
Flex Pipe
1 Exhaust Flex Pipe Bolts
M10 x 1.5
1
Exhaust Flex Pipe Bolts
M10 x 1.5
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Ensure gasket is properly seated before tightening.
Fuel
Torque specifications for Fuel
Fuel
Torque specifications for Fuel
Fuel Rail System
1 Fuel Rail Bolts
M6 x 1.0
1
Fuel Rail Bolts
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure the fuel rail is properly aligned before tightening.
2 Fuel Injector Bolts
M6 x 1.0
2
Fuel Injector Bolts
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure injectors are properly seated before tightening.
Fuel Pump System
1 Fuel Pump Mounting Bolts
M6 x 1.0
1
Fuel Pump Mounting Bolts
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure the fuel pump is properly aligned before tightening.
2 High-Pressure Fuel Pump Mounting Bolts
M8 x 1.25
2
High-Pressure Fuel Pump Mounting Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Estimated value based on similar high-pressure pump applications.
Fuel Tank System
1 Fuel Tank Strap Bolts
M10 x 1.5
1
Fuel Tank Strap Bolts
M10 x 1.5
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure the fuel tank is properly positioned before tightening.
2 Fuel Filler Neck Bolts
M6 x 1.0
2
Fuel Filler Neck Bolts
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure the filler neck is properly aligned before tightening.
3 Fuel Tank Sender Unit Bolts
M6 x 1.0
3
Fuel Tank Sender Unit Bolts
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Estimated value based on similar sender unit applications.
Fuel Filter And Regulator System
1 Fuel Filter Bolt/Nut
M8 x 1.25
1
Fuel Filter Bolt/Nut
M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Ensure the fuel filter is properly aligned before tightening.
2 Fuel Pressure Regulator Bolts
M6 x 1.0
2
Fuel Pressure Regulator Bolts
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure the regulator is properly seated before tightening.
Fuel Line System
1 Fuel Line Fittings
M8 x 1.25
1
Fuel Line Fittings
M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Ensure fittings are properly aligned before tightening.
Hvac
Torque specifications for Hvac
Hvac
Torque specifications for Hvac
Ac Compressor System
1 A/C Compressor Mounting Bolts
M10 x 1.5
1
A/C Compressor Mounting Bolts
M10 x 1.5
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
Ensure the compressor is aligned properly before tightening. Use a crisscross pattern for even torque distribution.
2 A/C Line Fittings
M8 x 1.25
2
A/C Line Fittings
M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Ensure fittings are clean and free of debris before assembly. Over-tightening can damage the O-ring seals.
Cooling System
1 Thermostat Housing Bolts
M6 x 1.0
1
Thermostat Housing Bolts
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Use a crisscross pattern to ensure even pressure on the housing gasket.
2 Water Pump Bolts
M6 x 1.0
2
Water Pump Bolts
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure the water pump is properly seated before tightening. Use a crisscross pattern for even torque distribution.
Heating System
1 Heater Core Inlet/Outlet Hose Clamps
N/A (Clamp)
1
Heater Core Inlet/Outlet Hose Clamps
N/A (Clamp)
Torque Specification
N/A
Important Notes
Hand-tighten clamps securely. Ensure hoses are fully seated on the heater core fittings.
2 Heater Core Mounting Bolts
M6 x 1.0
2
Heater Core Mounting Bolts
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure the heater core is properly seated before tightening. Use a crisscross pattern for even torque distribution.
Air Distribution System
1 Blower Motor Mounting Bolts
M6 x 1.0
1
Blower Motor Mounting Bolts
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure the blower motor is properly aligned before tightening. Use a crisscross pattern for even torque distribution.
2 Evaporator Core Housing Bolts
M6 x 1.0
2
Evaporator Core Housing Bolts
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure the housing is properly sealed to prevent refrigerant leaks. Use a crisscross pattern for even torque distribution.
3 Air Duct Clamps/Screws
N/A (Clamp/Screw)
3
Air Duct Clamps/Screws
N/A (Clamp/Screw)
Torque Specification
N/A
Important Notes
Hand-tighten clamps or screws securely. Ensure ducts are fully seated to prevent air leaks.
Control System
1 HVAC Control Panel Mounting Screws
M4 x 0.7
1
HVAC Control Panel Mounting Screws
M4 x 0.7
Torque Specification
2 ft-lbs (3 N·m)
Important Notes
Ensure the control panel is properly aligned before tightening. Over-tightening can damage the panel or mounting points.
Suspension
Torque specifications for Suspension
Suspension
Torque specifications for Suspension
Strut Shock Subsystem
1 Strut/Shock Absorber Mounting Bolts
M10 x 1.25
1
Strut/Shock Absorber Mounting Bolts
M10 x 1.25
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
Ensures proper function and prevents noise or failure.
2 Strut Tower Bolts
M12 x 1.5
2
Strut Tower Bolts
M12 x 1.5
Torque Specification
63 ft-lbs (85 N·m)
Important Notes
Prevents noise or detachment, ensuring alignment.
Control Arm Subsystem
1 Control Arm Bolts
M14 x 1.5
1
Control Arm Bolts
M14 x 1.5
Torque Specification
85 ft-lbs (115 N·m)
Important Notes
Ensures proper alignment and prevents excessive wear.
2 Ball Joint Nut
M12 x 1.25
2
Ball Joint Nut
M12 x 1.25
Torque Specification
52 ft-lbs (70 N·m)
Important Notes
Ensures smooth steering and prevents joint failure.
Steering Subsystem
1 Tie Rod End Nut
M10 x 1.25
1
Tie Rod End Nut
M10 x 1.25
Torque Specification
33 ft-lbs (45 N·m)
Important Notes
Prevents looseness or detachment, ensuring steering stability.
2 Steering Gear/Rack Bolts
M12 x 1.5
2
Steering Gear/Rack Bolts
M12 x 1.5
Torque Specification
59 ft-lbs (80 N·m)
Important Notes
Ensures precise steering control and prevents misalignment.
Sway Bar Subsystem
1 Sway Bar Link Nut
M10 x 1.25
1
Sway Bar Link Nut
M10 x 1.25
Torque Specification
33 ft-lbs (45 N·m)
Important Notes
Ensures effective sway bar function and reduces body roll.
2 Sway Bar Bracket Bolts
M8 x 1.25
2
Sway Bar Bracket Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensures the sway bar remains securely attached to the chassis.
Wheel Drivetrain Subsystem
1 CV Joint/Axle Nut
M24 x 1.5
1
CV Joint/Axle Nut
M24 x 1.5
Torque Specification
111 ft-lbs (150 N·m)
Important Notes
Prevents wheel detachment or excessive drivetrain play.
2 Wheel Lug Nuts
M12 x 1.5
2
Wheel Lug Nuts
M12 x 1.5
Torque Specification
89 ft-lbs (120 N·m)
Important Notes
Prevents wheel vibration or loosening, ensuring wheel attachment.
Subframe Subsystem
1 Subframe Mounting Bolts
M14 x 1.5
1
Subframe Mounting Bolts
M14 x 1.5
Torque Specification
81 ft-lbs (110 N·m)
Important Notes
Ensures the subframe remains securely attached to the chassis.
2 Rear Trailing Arm Bolts
M16 x 1.5
2
Rear Trailing Arm Bolts
M16 x 1.5
Torque Specification
95 ft-lbs (130 N·m)
Important Notes
Ensures proper alignment and prevents excessive wear in the rear suspension.
Troubleshooting Guide
Common issues, diagnostic steps, and prevention guidelines
Common Issues
Bolt stretching, stripped threads, uneven torque patterns
Common Issues
Bolt stretching, stripped threads, uneven torque patterns
Loose Components
Symptoms:
- Rattling or vibration noises
- Visible movement in components
- Uneven panel gaps
Solutions:
- Clean threads and mounting surfaces
- Replace damaged fasteners
- Apply proper torque in sequence
- Use thread locker if specified
Stripped Fasteners
Symptoms:
- Unable to achieve proper torque
- Fastener spins freely
- Visible thread damage
Solutions:
- Use thread repair kit if appropriate
- Install thread insert (HeliCoil)
- Replace component if threaded hole is damaged
- Upgrade to higher grade fastener if recommended
Overtightened Components
Symptoms:
- Cracked or deformed parts
- Broken fasteners
- Compressed gaskets or seals
Solutions:
- Replace damaged components
- Use new fasteners
- Follow proper torque sequence
- Verify correct torque specifications
Diagnostic Steps
Visual inspection, torque verification, thread assessment
Diagnostic Steps
Visual inspection, torque verification, thread assessment
1
Visual Inspection
Inspect the affected area for any visible signs of damage or wear
- Check for cracks or deformation
- Look for signs of excessive wear
- Verify proper fastener installation
2
Torque Verification
Verify the torque applied to the fasteners
- Check the torque wrench calibration
- Verify the torque specification
- Compare the applied torque to the specification
3
Thread Assessment
Assess the condition of the threads
- Check for signs of thread damage
- Verify the thread type and size
- Check for proper thread engagement
Prevention Guidelines
Best practices, maintenance tips, tool care
Prevention Guidelines
Best practices, maintenance tips, tool care
Best Practices
- Always follow the recommended torque specification
- Use the correct type and size of fasteners
- Verify the torque wrench calibration regularly
Maintenance Tips
- Regularly inspect the affected area for signs of wear or damage
- Replace damaged or worn-out components promptly
- Keep the work area clean and organized
Tool Care
- Regularly clean and maintain the torque wrench
- Store the torque wrench in a dry and secure location
- Verify the torque wrench calibration before each use
Frequently Asked Questions
Find answers to common questions about torque specifications
Q1 What IS the torque spec for the lug nuts on a 2020 Volkswagen Golf?
Q1
What IS the torque spec for the lug nuts on a 2020 Volkswagen Golf?
The torque spec for the lug nuts on a 2020 Volkswagen Golf IS 120 Nm (89 ft-lbs).
Q2 What IS the torque spec for the oil drain plug on a 2021 Volkswagen Golf?
Q2
What IS the torque spec for the oil drain plug on a 2021 Volkswagen Golf?
The torque spec for the oil drain plug on a 2021 Volkswagen Golf IS 30 Nm (22 ft-lbs).
Q3 What IS the torque spec for the spark plugs on a 2022 Volkswagen Golf?
Q3
What IS the torque spec for the spark plugs on a 2022 Volkswagen Golf?
The torque spec for the spark plugs on a 2022 Volkswagen Golf IS 25 Nm (18 ft-lbs).
Q4 What tools do I need to properly torque the bolts on my 2020 Volkswagen Golf?
Q4
What tools do I need to properly torque the bolts on my 2020 Volkswagen Golf?
You will need a torque wrench, a socket set, and a扳手.
Q5 How often should I check the torque on the bolts on my 2021 Volkswagen Golf?
Q5
How often should I check the torque on the bolts on my 2021 Volkswagen Golf?
You should check the torque on the bolts on your 2021 Volkswagen Golf every 6 months or 6,000 miles, whichever comes first.
Q6 What are the consequences of not properly torquing the bolts on my 2022 Volkswagen Golf?
Q6
What are the consequences of not properly torquing the bolts on my 2022 Volkswagen Golf?
Not properly torquing the bolts on your 2022 Volkswagen Golf can lead to the bolts coming loose, which can cause serious damage to your vehicle.
Environmental Considerations
Temperature, humidity, and seasonal effects on torque specifications
Temperature Effects
Includes: High Heat, Cold Weather, Thermal Cycling
Temperature Effects
Includes: High Heat, Cold Weather, Thermal Cycling
Temperature can significantly impact torque values and fastener behavior
Cold Weather
Effects:
- Increased material brittleness
- Higher torque required due to thread contraction
- Reduced thread lubricant effectiveness
Recommendations:
- Allow components to warm to room temperature when possible
- Consider using winter-grade thread lubricants
- Check torque values more frequently during winter months
Hot Weather
Effects:
- Thermal expansion of components
- Decreased friction in threads
- Accelerated lubricant breakdown
Recommendations:
- Check torque when components are at normal operating temperature
- Use temperature-resistant thread lockers
- Consider re-torquing after heat cycles
Humidity and Corrosion
Covers: Rust Prevention, Salt Exposure, Moisture Control
Humidity and Corrosion
Covers: Rust Prevention, Salt Exposure, Moisture Control
Moisture and corrosion can affect fastener integrity and torque values
High Humidity
Effects:
- Accelerated corrosion formation
- Reduced friction coefficient
- Potential thread seizing
Prevention:
- Use corrosion-resistant fasteners
- Apply appropriate anti-seize compounds
- Maintain proper protective coatings
Salt Exposure
Effects:
- Rapid corrosion development
- Thread damage
- Seized fasteners
Prevention:
- Regular underbody washing
- Use of sacrificial anodes where appropriate
- Application of protective coatings
Seasonal Maintenance
Spring, Summer, Fall, and Winter maintenance schedules
Seasonal Maintenance
Spring, Summer, Fall, and Winter maintenance schedules
Spring
- Inspect for winter damage
- Clean and protect exposed fasteners
- Check torque on critical components
Summer
- Monitor heat-affected components
- Check expansion-related loosening
- Inspect cooling system mounts
Fall
- Prepare for winter conditions
- Apply corrosion protection
- Verify all fasteners are properly torqued
Winter
- More frequent inspection of critical fasteners
- Check for salt damage
- Monitor suspension component torque
Related Resources
Tools, service procedures, and technical bulletins
Recommended Tools
Digital Torque Wrench (10-100 Nm)
For accurate tightening of fasteners. Ideal for application on the Golf.
- Digital display for precise readings
- Audible alarm for target torque
- Multiple units (Nm, ft-lb, in-lb)
- Reversible ratcheting mechanism
Service Procedures
Engine Components Bolt Tightening Sequence
Technical procedure for proper tightening of engine components.
- Tighten the cylinder head bolts in the correct sequence to 40 Nm.
- Tighten the camshaft bolts to 20 Nm.
- Tighten the crankshaft pulley bolt to 100 Nm.
Technical Service Bulletins
Legal Disclaimer
Important information about using this content
Always refer to your vehicle's service manual and take appropriate safety precautions when performing any maintenance or repairs.
General Information
The information provided on this website is for general informational purposes only. While we strive to maintain accuracy in our content, all specifications, procedures, and technical information should be verified against your vehicle's official service manual or with the manufacturer directly.
Warranty & Liability
The content on this website is provided "as is" without any representations or warranties, express or implied. We make no representations or warranties regarding the accuracy, completeness, or availability of the information.
We shall not be liable for any direct, indirect, special, or consequential damages arising from the use of information on this website.
Technical Information
- All specifications, including torque values, fluid capacities, and maintenance procedures, should be verified against your vehicle's factory service manual.
- Vehicle specifications and procedures may vary by model year, trim level, and region.
- Always follow the manufacturer's recommended procedures and safety precautions.
- Working on vehicles can be dangerous. Always take proper safety precautions and use appropriate safety equipment.
- If you're unsure about any procedure, consult a qualified professional mechanic.
Intellectual Property
All content, including text, images, and specifications, is protected by copyright and other intellectual property laws. Any unauthorized use or reproduction is prohibited.
About the Author
Expert automotive knowledge and experience
'/%3E%3Cpath d='M60 30a20 20 0 1 1 0 40 20 20 0 0 1 0-40zm0 45c16.5 0 30 7.5 30 16.8V100H30v-8.2c0-9.3 13.5-16.8 30-16.8z' fill='%23404040'/%3E%3C/svg%3E)
ASE
15+ Years
Experience
500+ Guides
Guides
50+ Makes
Vehicles
1000+ Solutions
Solutions
Diagnostic
Specialized in advanced diagnostic techniques using modern scan tools and oscilloscopes.
Repair
Expert in both traditional mechanical repairs and modern vehicle systems.
Additional Expertise
Documentation
Created over 500 detailed repair guides and technical documents.
Training
Conducted technical training sessions and contributed to repair databases.
Certifications & Research
Certifications
- ASE Master Technician Certification
- Advanced Diagnostic Specialist
- Hybrid/Electric Vehicle Systems
- Performance Tuning Expert
Research & Community
Actively researches emerging technologies and contributes to automotive forums.