Volkswagen Vehicle Models Volkswagen Jetta 2011-2018 Torque Specifications
Volkswagen Vehicle Models Volkswagen Jetta 2011-2018

Volkswagen Vehicle Models Volkswagen Jetta 2011-2018 Torque Specifications

Complete Volkswagen Vehicle Models Volkswagen Jetta 2011-2018 torque specifications guide. Includes factory-specified torque values, torque sequences, and technical specifications for all components including body, brakes, drivetrain, electrical, emissions sensors, fuel, exhaust, HVAC, and suspension. Essential information for proper assembly and maintenance.

Updated

Important Information

Safety guidelines and reference information for proper torque application

Quick Reference Guide
ft-lbs → Nm
× 1.356
ft-lbs → kg-m
× 0.138
Nm → ft-lbs
× 0.738
in-lbs → ft-lbs
× 0.083

Common Torque Patterns

Star Pattern

Used for wheels and other circular bolt patterns

Star Pattern torque pattern diagram showing proper bolt tightening sequence
Cross Pattern

Used for gaskets and cover plates

Cross Pattern torque pattern diagram showing proper bolt tightening sequence
Sequential Pattern

Used for head bolts and other critical components

Sequential Pattern torque pattern diagram showing proper bolt tightening sequence

Common Mistakes to Avoid

Over-tightening

Exceeding the specified torque value can stretch or break fasteners, damage threads, or crack components.

Prevention:

Always use a calibrated torque wrench and follow specifications exactly.

Incorrect Torque Sequence

Tightening bolts in the wrong order can cause uneven pressure distribution and potential leaks or damage.

Prevention:

Follow the manufacturer's specified torque sequence pattern.

Dirty Threads

Dirt, rust, or old thread locker can affect torque readings and proper fastener tension.

Prevention:

Clean and inspect all threads before assembly. Use new thread locker if specified.

Reusing TTY Bolts

Torque-to-yield bolts are designed to stretch and must not be reused.

Prevention:

Always replace TTY bolts with new ones. They are single-use only.

Dry vs. Lubricated

Not accounting for whether torque specs are for dry or lubricated fasteners can lead to incorrect tension.

Prevention:

Check if specs are for dry or lubricated threads. Use specified lubricant when required.

Recommended Tools

Torque Wrench (1/4" Drive)

Range: 2-25 ft-lbs
Small fasteners, delicate components

Torque Wrench (3/8" Drive)

Range: 10-100 ft-lbs
Most common automotive fasteners

Torque Wrench (1/2" Drive)

Range: 30-250 ft-lbs
Large fasteners, wheels

Angle Gauge

Torque-to-yield (TTY) bolts

Torque Wrench Care

  • Calibrate annually or after 5,000 clicks
  • Store at lowest setting
  • Keep clean and lubricated

Search Specifications

Search by component name, bolt size, or description

Torque Calculator

Convert between different torque units

1.2l I4 Engine

Torque specifications for 1.2L-I4 Engine

Cylinder Head

1

Cylinder Head Bolts

M10 x 1.5
Torque Specification
1. 18 ft-lbs (25 N·m) 2. 90°
Important Notes
Follow the manufacturer's specified torque sequence for the cylinder head bolts.
2

Valve Cover Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure the valve cover gasket is properly seated before tightening.

Crankshaft And Bearings

1

Main Bearing Bolts

M10 x 1.5
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Follow the manufacturer's specified torque sequence for main bearing bolts.
2

Flywheel Bolts

M12 x 1.5
Torque Specification
44 ft-lbs (60 N·m)
Important Notes
Ensure the flywheel is properly aligned before tightening.

Timing System

1

Timing Belt/Chain Tensioner Bolt

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure the tensioner is properly aligned before tightening.
2

Camshaft Sprocket Bolt

M10 x 1.5
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Ensure the camshaft is properly aligned before tightening.

Intake And Exhaust

1

Intake Manifold Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Follow the manufacturer's specified torque sequence for intake manifold bolts.
2

Exhaust Manifold Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Follow the manufacturer's specified torque sequence for exhaust manifold bolts.

Fuel System

1

Fuel Rail Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure the fuel rail is properly seated before tightening.
2

Fuel Injector Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure the fuel injectors are properly seated before tightening.

Cooling System

1

Water Pump Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure the water pump gasket is properly seated before tightening.
2

Thermostat Housing Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure the thermostat housing gasket is properly seated before tightening.

Turbocharger System

1

Turbocharger Mounting Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Follow the manufacturer's specified torque sequence for turbocharger mounting bolts.
2

Turbocharger Oil Feed Line Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure the oil feed line is properly seated before tightening.

1.2l I4 Turbo Engine

Torque specifications for 1.2L-I4-TURBO Engine

Cylinder Head

1

Cylinder Head Bolts

M10 x 1.5
Torque Specification
1. 18 ft-lbs (25 N·m) 2. 90°
Important Notes
Follow the manufacturer's specified torque sequence for the cylinder head bolts.
2

Valve Cover Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure the valve cover gasket is properly seated before tightening.

Crankshaft And Bearings

1

Main Bearing Bolts

M10 x 1.5
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Follow the manufacturer's specified torque sequence for main bearing bolts.
2

Flywheel Bolts

M12 x 1.5
Torque Specification
44 ft-lbs (60 N·m)
Important Notes
Ensure the flywheel is properly aligned before tightening.

Timing System

1

Timing Belt/Chain Tensioner Bolt

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure the tensioner is properly aligned before tightening.
2

Camshaft Sprocket Bolt

M10 x 1.5
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Ensure the camshaft is properly aligned before tightening.

Intake And Exhaust

1

Intake Manifold Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Follow the manufacturer's specified torque sequence for intake manifold bolts.
2

Exhaust Manifold Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Follow the manufacturer's specified torque sequence for exhaust manifold bolts.

Fuel System

1

Fuel Rail Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure the fuel rail is properly seated before tightening.
2

Fuel Injector Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure the fuel injectors are properly seated before tightening.

Cooling System

1

Water Pump Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure the water pump gasket is properly seated before tightening.
2

Thermostat Housing Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure the thermostat housing gasket is properly seated before tightening.

Turbocharger System

1

Turbocharger Mounting Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Follow the manufacturer's specified torque sequence for turbocharger mounting bolts.
2

Turbocharger Oil Feed Line Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure the oil feed line is properly seated before tightening.

1.4l I4 Engine

Torque specifications for 1.4L-I4 Engine

Cylinder Head and Engine Block

1

Cylinder Head Bolts

M12 x 1.5
Torque Specification
18 ft-lbs (25 N·m)
2

Main Bearing Bolts

M14 x 1.5
Torque Specification
18 ft-lbs (25 N·m)

Crankshaft and Connecting Rods

1

Connecting Rod Nuts

M10 x 1.5
Torque Specification
18 ft-lbs (25 N·m)
2

Flywheel Bolts

M14 x 1.5
Torque Specification
44 ft-lbs (60 N·m)

Valvetrain and Ignition

1

Valve Cover Bolts

M8 x 1.25
Torque Specification
7 ft-lbs (10 N·m)
2

Spark Plugs

M14 x 1.25
Torque Specification
18 ft-lbs (25 N·m)

Intake and Exhaust

1

Intake Manifold Bolts

M10 x 1.5
Torque Specification
18 ft-lbs (25 N·m)
2

Exhaust Manifold/Headers Bolts

M12 x 1.5
Torque Specification
18 ft-lbs (25 N·m)

Turbocharger and Intercooler

1

Turbocharger Mounting Bolts

M14 x 1.5
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
Estimated value, may vary depending on specific engine and application.
2

Intercooler Mounting Bolts

M12 x 1.5
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Estimated value, may vary depending on specific engine and application.

1.4l I4 Turbo Engine

Torque specifications for 1.4L-I4-TURBO Engine

Cylinder Head and Engine Block

1

Cylinder Head Bolts

M12 x 1.5
Torque Specification
18 ft-lbs (25 N·m)
2

Main Bearing Bolts

M14 x 1.5
Torque Specification
18 ft-lbs (25 N·m)

Crankshaft and Connecting Rods

1

Connecting Rod Nuts

M10 x 1.5
Torque Specification
18 ft-lbs (25 N·m)
2

Flywheel Bolts

M14 x 1.5
Torque Specification
44 ft-lbs (60 N·m)

Valvetrain and Ignition

1

Valve Cover Bolts

M8 x 1.25
Torque Specification
7 ft-lbs (10 N·m)
2

Spark Plugs

M14 x 1.25
Torque Specification
18 ft-lbs (25 N·m)

Intake and Exhaust

1

Intake Manifold Bolts

M10 x 1.5
Torque Specification
18 ft-lbs (25 N·m)
2

Exhaust Manifold/Headers Bolts

M12 x 1.5
Torque Specification
18 ft-lbs (25 N·m)

Turbocharger and Intercooler

1

Turbocharger Mounting Bolts

M14 x 1.5
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
Estimated value, may vary depending on specific engine and application.
2

Intercooler Mounting Bolts

M12 x 1.5
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Estimated value, may vary depending on specific engine and application.

1.8l I4 Engine

Torque specifications for 1.8L-I4 Engine

Cylinder Head

1

Cylinder Head Bolts

M10 x 1.5
Torque Specification
1. 18 ft-lbs (25 N·m) 2. 90°
Important Notes
Follow the specified torque sequence for even clamping force.

Crankshaft And Bearings

1

Main Bearing Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure proper alignment of main bearings during installation.
2

Connecting Rod Nuts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Use new nuts for reassembly to ensure proper clamping force.
3

Flywheel Bolts

M12 x 1.5
Torque Specification
44 ft-lbs (60 N·m)
Important Notes
Ensure the flywheel is properly aligned during installation.

Valve Train

1

Rocker Arms/Shafts Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure proper valve clearance after torquing.
2

Camshaft Sprocket Bolt

M10 x 1.5
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Ensure proper timing alignment before torquing.

Turbocharger System

1

Turbocharger Mounting Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Estimated value based on similar components.
2

Turbocharger Oil Feed Line Bolts

M6 x 1.0
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Estimated value based on similar components.

1.8l I4 Turbo Engine

Torque specifications for 1.8L-I4-TURBO Engine

Cylinder Head

1

Cylinder Head Bolts

M10 x 1.5
Torque Specification
1. 18 ft-lbs (25 N·m) 2. 90°
Important Notes
Follow the specified torque sequence for even clamping force.

Crankshaft And Bearings

1

Main Bearing Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure proper alignment of main bearings during installation.
2

Connecting Rod Nuts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Use new nuts for reassembly to ensure proper clamping force.
3

Flywheel Bolts

M12 x 1.5
Torque Specification
44 ft-lbs (60 N·m)
Important Notes
Ensure the flywheel is properly aligned during installation.

Valve Train

1

Rocker Arms/Shafts Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure proper valve clearance after torquing.
2

Camshaft Sprocket Bolt

M10 x 1.5
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Ensure proper timing alignment before torquing.

Turbocharger System

1

Turbocharger Mounting Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Estimated value based on similar components.
2

Turbocharger Oil Feed Line Bolts

M6 x 1.0
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Estimated value based on similar components.

2.0l I4 Engine

Torque specifications for 2.0L-I4 Engine

Cylinder Head

1

Cylinder Head Bolts

M10 x 1.5
Torque Specification
1. 18 ft-lbs (25 N·m) 2. 90°
Important Notes
Follow the manufacturer's specified torque sequence to ensure even clamping force.
2

Valve Cover Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure the valve cover gasket is properly seated before tightening.

Crankshaft And Bearings

1

Main Bearing Bolts

M10 x 1.5
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure the crankshaft is properly aligned before tightening.
2

Connecting Rod Nuts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure the connecting rod bearings are properly installed.
3

Flywheel Bolts

M12 x 1.5
Torque Specification
44 ft-lbs (60 N·m)
Important Notes
Use thread locker on the flywheel bolts as specified by the manufacturer.

Timing System

1

Timing Belt/Chain Tensioner Bolt

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure proper tension on the timing belt/chain before tightening.
2

Camshaft Sprocket Bolt

M10 x 1.5
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Ensure the camshaft is properly aligned before tightening.
3

Crankshaft Pulley/Harmonic Balancer Bolt

M14 x 1.5
Torque Specification
81 ft-lbs (110 N·m)
Important Notes
Use a holding tool to prevent the crankshaft from rotating during tightening.

Intake And Exhaust

1

Intake Manifold Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure the intake manifold gasket is properly seated before tightening.
2

Exhaust Manifold/Headers Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure the exhaust manifold gasket is properly seated before tightening.
3

Fuel Rail Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure the fuel injectors are properly seated before tightening.

Lubrication System

1

Oil Pan Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Ensure the oil pan gasket is properly seated before tightening.
2

Oil Filter Housing Bolt

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure the oil filter housing gasket is properly seated before tightening.
3

Oil Drain Plug Bolt

M12 x 1.5
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Replace the crush washer to prevent leaks.

Turbocharger System

1

Turbocharger Mounting Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Estimated value based on similar components. Ensure proper alignment before tightening.
2

Turbocharger Oil Feed Line Bolt

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Estimated value based on similar components. Ensure proper sealing of the oil feed line.
3

Turbocharger Oil Return Line Bolt

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Estimated value based on similar components. Ensure proper sealing of the oil return line.
4

Turbocharger Coolant Line Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Estimated value based on similar components. Ensure proper sealing of the coolant lines.
5

Intercooler Mounting Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Estimated value based on similar components. Ensure proper alignment before tightening.

2.0l I4 Turbo Engine

Torque specifications for 2.0L-I4-TURBO Engine

Cylinder Head

1

Cylinder Head Bolts

M10 x 1.5
Torque Specification
1. 18 ft-lbs (25 N·m) 2. 90°
Important Notes
Follow the manufacturer's specified torque sequence to ensure even clamping force.
2

Valve Cover Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure the valve cover gasket is properly seated before tightening.

Crankshaft And Bearings

1

Main Bearing Bolts

M10 x 1.5
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure the crankshaft is properly aligned before tightening.
2

Connecting Rod Nuts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure the connecting rod bearings are properly installed.
3

Flywheel Bolts

M12 x 1.5
Torque Specification
44 ft-lbs (60 N·m)
Important Notes
Use thread locker on the flywheel bolts as specified by the manufacturer.

Timing System

1

Timing Belt/Chain Tensioner Bolt

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure proper tension on the timing belt/chain before tightening.
2

Camshaft Sprocket Bolt

M10 x 1.5
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Ensure the camshaft is properly aligned before tightening.
3

Crankshaft Pulley/Harmonic Balancer Bolt

M14 x 1.5
Torque Specification
81 ft-lbs (110 N·m)
Important Notes
Use a holding tool to prevent the crankshaft from rotating during tightening.

Intake And Exhaust

1

Intake Manifold Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure the intake manifold gasket is properly seated before tightening.
2

Exhaust Manifold/Headers Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure the exhaust manifold gasket is properly seated before tightening.
3

Fuel Rail Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure the fuel injectors are properly seated before tightening.

Lubrication System

1

Oil Pan Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Ensure the oil pan gasket is properly seated before tightening.
2

Oil Filter Housing Bolt

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure the oil filter housing gasket is properly seated before tightening.
3

Oil Drain Plug Bolt

M12 x 1.5
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Replace the crush washer to prevent leaks.

Turbocharger System

1

Turbocharger Mounting Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Estimated value based on similar components. Ensure proper alignment before tightening.
2

Turbocharger Oil Feed Line Bolt

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Estimated value based on similar components. Ensure proper sealing of the oil feed line.
3

Turbocharger Oil Return Line Bolt

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Estimated value based on similar components. Ensure proper sealing of the oil return line.
4

Turbocharger Coolant Line Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Estimated value based on similar components. Ensure proper sealing of the coolant lines.
5

Intercooler Mounting Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Estimated value based on similar components. Ensure proper alignment before tightening.

Body

Torque specifications for Body

Wheels And Suspension

1

Wheel Lug Nuts

M12 x 1.5
Torque Specification
90 ft-lbs (122 N·m)
Important Notes
Ensure lug nuts are tightened in a star pattern to evenly distribute torque.
2

Strut/Shock Absorber Mounting Bolts

M10 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure bolts are tightened with the vehicle at ride height to avoid preloading the suspension.
3

Control Arm Bolts

M12 x 1.5
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Ensure the vehicle is at ride height before tightening to avoid preloading the suspension.
4

Ball Joint Nut

M14 x 1.5
Torque Specification
70 ft-lbs (95 N·m)
Important Notes
Ensure the ball joint is properly seated before tightening.
5

Tie Rod End Nut

M12 x 1.25
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Ensure the tie rod end is properly aligned before tightening.
6

Sway Bar Link Nut

M10 x 1.25
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Ensure the sway bar link is properly aligned before tightening.
7

Steering Gear/Rack Bolts

M10 x 1.25
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Ensure the steering rack is properly aligned before tightening.

Fuel System

1

Fuel Tank Strap Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure the fuel tank is properly aligned before tightening.
2

Fuel Filler Neck Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure the fuel filler neck is properly aligned before tightening.

Electrical System

1

Battery Terminal Nuts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure the battery terminals are clean and free of corrosion before tightening.

Body And Interior

1

Door Hinge Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure the door is properly aligned before tightening.
2

Seat Belt Anchor Bolts

M10 x 1.25
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Ensure the seat belt anchor is properly aligned before tightening.
3

Seat Mounting Bolts

M10 x 1.25
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Ensure the seat is properly aligned before tightening.
4

Hood Hinge Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure the hood is properly aligned before tightening.
5

Trunk Lid Hinge Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure the trunk lid is properly aligned before tightening.
6

Bumper Mounting Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure the bumper is properly aligned before tightening.
7

Roof Rack Mounting Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure the roof rack is properly aligned before tightening.

Brakes

Torque specifications for Brakes

Brake Caliper

1

Brake Caliper Bolts

M10 x 1.25
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
These bolts secure the brake caliper to the mounting bracket. Proper torque prevents movement or misalignment.
2

Brake Caliper Mounting Bracket Bolts

M12 x 1.5
Torque Specification
80 ft-lbs (108 N·m)
Important Notes
These bolts attach the caliper mounting bracket to the steering knuckle or axle. Critical for structural integrity.

Brake Disc Drum

1

Brake Disc/Drum Retaining Bolts

M12 x 1.25
Torque Specification
75 ft-lbs (102 N·m)
Important Notes
These bolts secure the brake disc or drum to the wheel hub. Proper torque prevents vibrations or wobbling.

Brake Hydraulics

1

Brake Hose Banjo Bolt

M10 x 1.0
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
This bolt connects the brake hose to the caliper or brake line. Proper torque ensures a leak-free connection.
2

Brake Master Cylinder Mounting Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
These bolts secure the master cylinder to the brake booster or firewall. Proper torque prevents leaks or misalignment.

Brake Booster

1

Brake Booster Mounting Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
These bolts secure the brake booster to the firewall. Proper torque ensures stable operation.

Brake Pedal

1

Brake Pedal Assembly Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
These bolts secure the brake pedal assembly to the firewall or bracket. Proper torque ensures smooth operation.

Abs System

1

ABS Sensor Mounting Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
These bolts secure the ABS wheel speed sensor to the steering knuckle or axle. Proper torque ensures accurate wheel speed data.

Wheel Assembly

1

Wheel Lug Nuts

M12 x 1.5
Torque Specification
90 ft-lbs (122 N·m)
Important Notes
These nuts secure the wheel to the hub. Proper torque prevents loosening or detachment.

Dq200 Transmission

Torque specifications for Dq200 Transmission

Transmission Mounting

1

Transmission Mounting Bolts

M10 x 1.5
Torque Specification
44 ft-lbs (60 N·m)
Important Notes
Ensure proper alignment of the transmission during installation.
2

Transmission Bellhousing Bolts

M10 x 1.5
Torque Specification
44 ft-lbs (60 N·m)
Important Notes
Ensure proper alignment with the engine block.

Oil Pan And Fluid Management

1

Transmission Oil Pan Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Avoid over-tightening to prevent damage to the oil pan or gasket.
2

Transmission Drain and Fill Plugs

M12 x 1.5
Torque Specification
29 ft-lbs (40 N·m)
Important Notes
Ensure proper sealing to prevent leaks.

Drivetrain Connection

1

Drive Axle/Half Shaft Bolts

M10 x 1.5
Torque Specification
44 ft-lbs (60 N·m)
Important Notes
Ensure proper alignment of the drive axles.
2

CV Joint/Axle Nut

M24 x 1.5
Torque Specification
148 ft-lbs (200 N·m)
Important Notes
Ensure the axle is fully seated before torquing.
3

Propeller/Drive Shaft Bolts

M10 x 1.5
Torque Specification
44 ft-lbs (60 N·m)
Important Notes
Ensure proper alignment of the drive shaft.

Clutch And Shift Components

1

Clutch Pressure Plate Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure proper alignment of the clutch pressure plate.
2

Transmission Shift Linkage Bolts

M6 x 1.0
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure proper alignment of the shift linkage.

Control Module And Cooling

1

Transmission Control Module Mounting Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure the TCM is securely mounted to prevent electrical issues.
2

Transmission Cooler Line Fittings

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure proper sealing to prevent fluid leaks.

Dq250 Transmission

Torque specifications for Dq250 Transmission

Transmission Mounting

1

Transmission Mounting Bolts

M10 x 1.5
Torque Specification
44 ft-lbs (60 N·m)
Important Notes
Ensure proper alignment of the transmission before tightening.
2

Transmission Bellhousing Bolts

M10 x 1.5
Torque Specification
44 ft-lbs (60 N·m)
Important Notes
Critical for proper alignment between the transmission and engine.
3

Transmission Crossmember Bolts

M10 x 1.5
Torque Specification
44 ft-lbs (60 N·m)
Important Notes
Ensures proper support and reduces vibrations.

Fluid Management

1

Transmission Oil Pan Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Prevents leaks and ensures a proper seal.
2

Transmission Drain Plug

M14 x 1.5
Torque Specification
29 ft-lbs (40 N·m)
Important Notes
Prevents leaks and ensures proper seating.
3

Transmission Fill Plug

M14 x 1.5
Torque Specification
29 ft-lbs (40 N·m)
Important Notes
Prevents leaks and ensures proper seating.
4

Transmission Cooler Line Fittings

M12 x 1.5
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Prevents leaks and ensures proper fluid flow.

Drivetrain Connection

1

Drive Axle/Half Shaft Bolts

M10 x 1.5
Torque Specification
44 ft-lbs (60 N·m)
Important Notes
Ensures secure attachment of the drive axles.
2

CV Joint/Axle Nut

M24 x 1.5
Torque Specification
148 ft-lbs (200 N·m)
Important Notes
Critical for securing the CV joint to the wheel hub.
3

Propeller/Drive Shaft Bolts

M10 x 1.5
Torque Specification
44 ft-lbs (60 N·m)
Important Notes
Ensures secure attachment of the drive shaft.

Torque Converter

1

Torque Converter Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensures secure attachment of the torque converter.

Control Systems

1

Shift Linkage Bolts

M6 x 1.0
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensures smooth shifting and proper alignment.
2

Transmission Control Module (TCM) Mounting Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensures secure mounting and proper grounding of the TCM.

Starter Motor

1

Starter Motor Mounting Bolts

M8 x 1.25
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
Ensures secure attachment and proper alignment of the starter motor.

Drivetrain

Torque specifications for Drivetrain

Flywheel And Clutch

1

Flywheel Bolts

M10 x 1.25
Torque Specification
44 ft-lbs (60 N·m)
Important Notes
Ensure bolts are tightened in a star pattern to evenly distribute torque.
2

Clutch Pressure Plate Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure bolts are tightened in a star pattern to evenly distribute torque.

Transmission

1

Transmission Mounting Bolts

M10 x 1.25
Torque Specification
44 ft-lbs (60 N·m)
Important Notes
Ensure transmission is properly aligned before tightening bolts.
2

Transmission Bellhousing Bolts

M10 x 1.25
Torque Specification
44 ft-lbs (60 N·m)
Important Notes
Ensure bolts are tightened in a star pattern to evenly distribute torque.
3

Transmission Oil Pan Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Ensure oil pan gasket is properly seated before tightening bolts.
4

Transmission Drain and Fill Plugs

M12 x 1.5
Torque Specification
29 ft-lbs (40 N·m)
Important Notes
Ensure plugs are properly sealed to prevent fluid leaks.

Driveshaft And Axles

1

Drive Axle/Half Shaft Bolts

M10 x 1.25
Torque Specification
44 ft-lbs (60 N·m)
Important Notes
Ensure axles are properly seated before tightening bolts.
2

CV Joint/Axle Nut

M24 x 1.5
Torque Specification
148 ft-lbs (200 N·m)
Important Notes
Ensure axle is properly seated before tightening nut.
3

Propeller/Drive Shaft Bolts

M10 x 1.25
Torque Specification
44 ft-lbs (60 N·m)
Important Notes
Ensure drive shaft is properly aligned before tightening bolts.
4

Driveshaft Center Support Bearing Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure center support bearing is properly aligned before tightening bolts.

Differential And Transfer Case

1

Differential Mounting Bolts

M10 x 1.25
Torque Specification
44 ft-lbs (60 N·m)
Important Notes
Ensure differential is properly aligned before tightening bolts.
2

Differential Drain/Fill Plug

M12 x 1.5
Torque Specification
29 ft-lbs (40 N·m)
Important Notes
Ensure plugs are properly sealed to prevent fluid leaks.
3

Transfer Case Mounting Bolts

M10 x 1.25
Torque Specification
44 ft-lbs (60 N·m)
Important Notes
Ensure transfer case is properly aligned before tightening bolts.
4

Transfer Case Drain/Fill Plug

M12 x 1.5
Torque Specification
29 ft-lbs (40 N·m)
Important Notes
Ensure plugs are properly sealed to prevent fluid leaks.

Electrical

Torque specifications for Electrical

Ignition System

1

Ignition Coil Bolt

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure proper alignment of the ignition coil to avoid damage to the spark plug boot.

Battery System

1

Battery Terminal Nut

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Avoid over-tightening to prevent damage to the battery terminals.
2

Ground Strap Bolt

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Estimated value based on similar electrical grounding components.

Charging System

1

Alternator Mounting Bolt

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure the alternator is properly aligned with the drive belt.

Starting System

1

Starter Motor Mounting Bolt

M10 x 1.5
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
Ensure the starter motor is properly aligned with the flywheel.

Ac System

1

A/C Compressor Mounting Bolt

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure the compressor is properly aligned with the drive belt.
2

A/C Line Fitting

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure the fittings are properly aligned to avoid leaks.

Electrical Control Units

1

ECU/ECM Mounting Bolt

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Estimated value based on similar electrical components.
2

Fuse Box Mounting Bolt

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Estimated value based on similar electrical components.

Lighting System

1

Headlight Housing Bolt

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Estimated value based on similar electrical components.

Wiring Harness

1

Wiring Harness Retaining Bolt

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Estimated value based on similar electrical components.

Emissions Sensors

Torque specifications for Emissions_sensors

Egr System

1

EGR Valve Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure the EGR valve is properly aligned before tightening.

Exhaust Manifold

1

Exhaust Manifold/Headers Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Follow the manufacturer's recommended torque sequence.
2

Exhaust Manifold/Headers to Cylinder Head Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure the manifold is properly aligned with the cylinder head.

Exhaust Pipe

1

Exhaust Pipe to Exhaust Manifold/Headers Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure the gasket is properly seated before tightening.
2

Catalytic Converter to Exhaust Pipe Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure the gasket is properly seated before tightening.

Emissions Sensors

1

Oxygen Sensor (O2 Sensor) Mounting

M18 x 1.5
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Estimated value based on typical O2 sensor torque specifications.
2

NOx Sensor Mounting

M18 x 1.5
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Estimated value based on typical NOx sensor torque specifications.
3

Exhaust Gas Temperature Sensor Mounting

M12 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Estimated value based on typical exhaust gas temperature sensor torque specifications.

Diesel Particulate Filter

1

DPF Mounting Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Follow the manufacturer's recommended torque sequence.

Exhaust

Torque specifications for Exhaust

Exhaust Manifold and Headers

1

Exhaust Manifold/Headers to Engine Block Bolts

M12 x 1.5
Torque Specification
18 ft-lbs (25 N·m)
2

Exhaust Manifold/Headers to Cylinder Head Bolts

M12 x 1.5
Torque Specification
18 ft-lbs (25 N·m)

Exhaust Pipe and Components

1

Exhaust Pipe to Exhaust Manifold/Headers Bolts

M12 x 1.5
Torque Specification
18 ft-lbs (25 N·m)
2

Catalytic Converter to Exhaust Pipe Bolts

M12 x 1.5
Torque Specification
18 ft-lbs (25 N·m)
3

Muffler to Exhaust Pipe Bolts

M12 x 1.5
Torque Specification
18 ft-lbs (25 N·m)

Exhaust System Mounting and Hangers

1

Exhaust System Mounting Bracket Bolts

M14 x 1.5
Torque Specification
22.5 ft-lbs (30.5 N·m)
Important Notes
Estimated value based on general industry standards.
2

Exhaust System Hanger Bolts

M14 x 1.5
Torque Specification
22.5 ft-lbs (30.5 N·m)
Important Notes
Estimated value based on general industry standards.

Heat Shields and Oxygen Sensors

1

Heat Shield Bolts

M10 x 1.5
Torque Specification
12.5 ft-lbs (17 N·m)
Important Notes
Estimated value based on general industry standards.
2

Oxygen Sensor Bolts

M12 x 1.5
Torque Specification
17.5 ft-lbs (23.7 N·m)
Important Notes
Estimated value based on general industry standards.

Fuel

Torque specifications for Fuel

Fuel Delivery System

1

Fuel Rail Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure bolts are tightened in a crisscross pattern to evenly distribute pressure.
2

Fuel Injector Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure injectors are properly seated before tightening.
3

Fuel Pump Mounting Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure the fuel pump is properly aligned before tightening.
4

High-Pressure Fuel Pump Mounting Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure bolts are tightened in a crisscross pattern to evenly distribute pressure.

Fuel Storage System

1

Fuel Tank Strap Bolts

M10 x 1.5
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure the fuel tank is properly aligned before tightening.
2

Fuel Filler Neck Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure the filler neck is properly aligned before tightening.
3

Fuel Tank Sender Unit Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure the sender unit is properly seated before tightening.

Fuel Filtration System

1

Fuel Filter Bolt/Nut

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure the filter is properly aligned before tightening.

Fuel Regulation System

1

Fuel Pressure Regulator Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure the regulator is properly seated before tightening.
2

Fuel Line Fittings

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure fittings are properly aligned before tightening.

Hvac

Torque specifications for Hvac

Ac Compressor

1

A/C Compressor Mounting Bolts

M10 x 1.5
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure bolts are tightened in a crisscross pattern to avoid uneven stress on the compressor.
2

A/C Line Fittings

M10 x 1.5
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure fittings are clean and free of debris before installation.

Evaporator

1

Evaporator Housing Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Estimated value based on similar M6 bolts in HVAC systems.

Blower Motor

1

Blower Motor Mounting Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Estimated value based on similar M6 bolts in HVAC systems.

Heater Core

1

Heater Core Inlet/Outlet Fittings

M10 x 1.5
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure fittings are clean and free of debris before installation.

Condenser

1

Condenser Mounting Bolts

M10 x 1.5
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure bolts are tightened in a crisscross pattern to avoid uneven stress on the condenser.

Control Panel

1

HVAC Control Panel Mounting Screws

M5 x 0.8
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Estimated value based on similar M5 screws in HVAC systems.

Suspension

Torque specifications for Suspension

Strut Shock Absorber

1

Strut/Shock Absorber Mounting Bolts

M10 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure bolts are tightened evenly to avoid misalignment.

Control Arm

1

Control Arm Bolts

M12 x 1.75
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Ensure the control arm is properly aligned before tightening.

Ball Joint

1

Ball Joint Nut

M14 x 1.5
Torque Specification
70 ft-lbs (95 N·m)
Important Notes
Ensure the ball joint is seated properly before tightening.

Tie Rod

1

Tie Rod End Nut

M12 x 1.25
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Ensure the tie rod end is properly aligned before tightening.

Sway Bar

1

Sway Bar Link Nut

M10 x 1.25
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Ensure the sway bar link is properly aligned before tightening.

Steering Gear

1

Steering Gear/Rack Bolts

M12 x 1.75
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Ensure the steering rack is properly aligned before tightening.

Wheel Lug

1

Wheel Lug Nuts

M12 x 1.5
Torque Specification
90 ft-lbs (122 N·m)
Important Notes
Use a star pattern to tighten lug nuts evenly.

Drive Axle

1

Drive Axle/Half Shaft Bolts

M10 x 1.25
Torque Specification
44 ft-lbs (60 N·m)
Important Notes
Ensure the drive axle is properly seated before tightening.

Cv Joint

1

CV Joint/Axle Nut

M24 x 1.5
Torque Specification
148 ft-lbs (200 N·m)
Important Notes
Ensure the CV joint is properly seated before tightening.

Subframe

1

Subframe Mounting Bolts

M14 x 1.5
Torque Specification
74 ft-lbs (100 N·m)
Important Notes
Tighten bolts in a crisscross pattern to ensure even pressure.

Rear Suspension Trailing Arm

1

Rear Suspension Trailing Arm Bolts

M12 x 1.75
Torque Specification
66 ft-lbs (90 N·m)
Important Notes
Ensure the trailing arm is properly aligned before tightening.

Front Suspension Knuckle

1

Front Suspension Knuckle Bolts

M14 x 1.5
Torque Specification
81 ft-lbs (110 N·m)
Important Notes
Ensure the steering knuckle is properly aligned before tightening.

Rear Suspension Crossmember

1

Rear Suspension Crossmember Bolts

M14 x 1.5
Torque Specification
74 ft-lbs (100 N·m)
Important Notes
Tighten bolts in a crisscross pattern to ensure even pressure.

Troubleshooting Guide

Common issues, diagnostic steps, and prevention guidelines

Common Issues

Bolt stretching, stripped threads, uneven torque patterns

Loose Components

Symptoms:
  • Rattling or vibration noises
  • Visible movement in components
  • Uneven panel gaps
Solutions:
  • Clean threads and mounting surfaces
  • Replace damaged fasteners
  • Apply proper torque in sequence
  • Use thread locker if specified

Stripped Fasteners

Symptoms:
  • Unable to achieve proper torque
  • Fastener spins freely
  • Visible thread damage
Solutions:
  • Use thread repair kit if appropriate
  • Install thread insert (HeliCoil)
  • Replace component if threaded hole is damaged
  • Upgrade to higher grade fastener if recommended

Overtightened Components

Symptoms:
  • Cracked or deformed parts
  • Broken fasteners
  • Compressed gaskets or seals
Solutions:
  • Replace damaged components
  • Use new fasteners
  • Follow proper torque sequence
  • Verify correct torque specifications

Diagnostic Steps

Visual inspection, torque verification, thread assessment

1

Visual Inspection

Inspect the affected area for any visible signs of damage or wear

  • Check for cracks or deformation
  • Look for signs of excessive wear
  • Verify proper fastener installation
2

Torque Verification

Verify the torque applied to the fasteners

  • Check the torque wrench calibration
  • Verify the torque specification
  • Compare the applied torque to the specification
3

Thread Assessment

Assess the condition of the threads

  • Check for signs of thread damage
  • Verify the thread type and size
  • Check for proper thread engagement

Prevention Guidelines

Best practices, maintenance tips, tool care

Best Practices

  • Always follow the recommended torque specification
  • Use the correct type and size of fasteners
  • Verify the torque wrench calibration regularly

Maintenance Tips

  • Regularly inspect the affected area for signs of wear or damage
  • Replace damaged or worn-out components promptly
  • Keep the work area clean and organized

Tool Care

  • Regularly clean and maintain the torque wrench
  • Store the torque wrench in a dry and secure location
  • Verify the torque wrench calibration before each use

Frequently Asked Questions

Find answers to common questions about torque specifications

Q1

What are the general torque specifications for engine components on a 2011-2018 Volkswagen Jetta?

Tighten cylinder head bolts to 40 Nm (30 lb-ft) in three stages and then an additional 90 degrees. Tighten intake and exhaust manifold bolts to 25 Nm (18 lb-ft). Tighten valve cover bolts to 10 Nm (7 lb-ft).

Q2

What special tools are required for torque-related procedures on the Jetta?

A torque wrench and appropriate sized sockets are essential for accurate torque application. An angle gauge may be required for specific components where torque plus angle tightening IS specified.

Q3

What IS the recommended torque for brake components on a 2011-2018 Volkswagen Jetta?

Tighten lug bolts to 120 Nm (89 lb-ft). Tighten brake caliper bolts to 90 Nm (66 lb-ft). Tighten brake rotor screws to 7 Nm (5 lb-ft).

Q4

How do I ensure proper torque application when working on the suspension system?

Clean and inspect all bolts and threads before applying torque. Use a torque wrench calibrated to the specified torque value. Tighten bolts to the specified torque in a star pattern to ensure even distribution of force.

Q5

What are the torque specifications for the camshaft and timing components?

Tighten camshaft bolts to 60 Nm (44 lb-ft) plus 90 degrees. Tighten timing belt tensioner bolts to 20 Nm (15 lb-ft). Tighten crankshaft pulley bolt to 150 Nm (111 lb-ft) plus 180 degrees.

Q6

How often should I check and adjust torque on critical components?

Torque specifications should be checked and adjusted according to the manufacturer's recommended maintenance schedule. Critical components such as engine bolts, suspension components, and brake components should be checked more frequently, especially after major repairs or modifications.

Environmental Considerations

Temperature, humidity, and seasonal effects on torque specifications

Temperature Effects

Includes: High Heat, Cold Weather, Thermal Cycling

Temperature can significantly impact torque values and fastener behavior

Cold Weather

Effects:
  • Increased material brittleness
  • Higher torque required due to thread contraction
  • Reduced thread lubricant effectiveness
Recommendations:
  • Allow components to warm to room temperature when possible
  • Consider using winter-grade thread lubricants
  • Check torque values more frequently during winter months

Hot Weather

Effects:
  • Thermal expansion of components
  • Decreased friction in threads
  • Accelerated lubricant breakdown
Recommendations:
  • Check torque when components are at normal operating temperature
  • Use temperature-resistant thread lockers
  • Consider re-torquing after heat cycles

Humidity and Corrosion

Covers: Rust Prevention, Salt Exposure, Moisture Control

Moisture and corrosion can affect fastener integrity and torque values

High Humidity

Effects:
  • Accelerated corrosion formation
  • Reduced friction coefficient
  • Potential thread seizing
Prevention:
  • Use corrosion-resistant fasteners
  • Apply appropriate anti-seize compounds
  • Maintain proper protective coatings

Salt Exposure

Effects:
  • Rapid corrosion development
  • Thread damage
  • Seized fasteners
Prevention:
  • Regular underbody washing
  • Use of sacrificial anodes where appropriate
  • Application of protective coatings

Seasonal Maintenance

Spring, Summer, Fall, and Winter maintenance schedules

Spring

  • Inspect for winter damage
  • Clean and protect exposed fasteners
  • Check torque on critical components

Summer

  • Monitor heat-affected components
  • Check expansion-related loosening
  • Inspect cooling system mounts

Fall

  • Prepare for winter conditions
  • Apply corrosion protection
  • Verify all fasteners are properly torqued

Winter

  • More frequent inspection of critical fasteners
  • Check for salt damage
  • Monitor suspension component torque

Related Resources

Tools, service procedures, and technical bulletins

Recommended Tools

Digital Torque Wrench (10-100 Nm)

Essential for tightening fasteners to precise torque specifications, preventing damage and ensuring proper assembly. This range IS suitable for many applications on the Jetta.

  • Digital display for accurate readings
  • Audible alarm when target torque IS reached
  • Multiple units (Nm, ft-lb, in-lb)
  • Reversible ratcheting mechanism
Learn more
Service Procedures
Technical Service Bulletins

Legal Disclaimer

Important information about using this content

Always refer to your vehicle's service manual and take appropriate safety precautions when performing any maintenance or repairs.

General Information
The information provided on this website is for general informational purposes only. While we strive to maintain accuracy in our content, all specifications, procedures, and technical information should be verified against your vehicle's official service manual or with the manufacturer directly.
Warranty & Liability

The content on this website is provided "as is" without any representations or warranties, express or implied. We make no representations or warranties regarding the accuracy, completeness, or availability of the information.

We shall not be liable for any direct, indirect, special, or consequential damages arising from the use of information on this website.

Technical Information
  • All specifications, including torque values, fluid capacities, and maintenance procedures, should be verified against your vehicle's factory service manual.
  • Vehicle specifications and procedures may vary by model year, trim level, and region.
  • Always follow the manufacturer's recommended procedures and safety precautions.
  • Working on vehicles can be dangerous. Always take proper safety precautions and use appropriate safety equipment.
  • If you're unsure about any procedure, consult a qualified professional mechanic.
Intellectual Property
All content, including text, images, and specifications, is protected by copyright and other intellectual property laws. Any unauthorized use or reproduction is prohibited.

About the Author

Expert automotive knowledge and experience

Alan Montanye - Automotive Technical Specialist
ASE

Alan Montanye

Automotive Technical Specialist

ASE Master Certified Technician with over a decade of hands-on experience in automotive repair and diagnostics.

Facebook Contact
15+ Years
Experience
500+ Guides
Guides
50+ Makes
Vehicles
1000+ Solutions
Solutions

Diagnostic

Specialized in advanced diagnostic techniques using modern scan tools and oscilloscopes.

Repair

Expert in both traditional mechanical repairs and modern vehicle systems.

Additional Expertise

Documentation

Created over 500 detailed repair guides and technical documents.

Training

Conducted technical training sessions and contributed to repair databases.

Certifications & Research

Certifications

  • ASE Master Technician Certification
  • Advanced Diagnostic Specialist
  • Hybrid/Electric Vehicle Systems
  • Performance Tuning Expert

Research & Community

Actively researches emerging technologies and contributes to automotive forums.

© 2025 Volkswagen Specs. All rights reserved.

Privacy Policy Terms of Service